Manuals / Accton Technology / Computer Equipment / Switch

Accton Technology ES3002-TF manual Configuration, Switch Integrity

Models: ES3002-TF

1 58

Download 58 pages 50.96 Kb

Page 39

Configuration

Fast SwitcHub-2se User’s Guide

Configuration

If problems occur after altering the network configuration, restore the original connections, then try to track the problem down by implementing the new changes, one step at a time. Ensure that cable distances and other physical aspects of the installation do not exceed recommendations.

Switch Integrity

As a last resort verify the switch’s integrity with a power-on reset. Turn the power to the switch off and then on. If the problem still persists and you have completed all the preceding diagnoses, contact your Accton distributor for further assistance. (Refer to Appendix E.)

Troubleshooting

A-3

Image 39

Accton Technology ES3002-TF manual Configuration, Switch Integrity

Contents

INOGGODJI*IPG SwitcHub-2sewith one 10BASE-T/100BASE-TX Port and one 100BASE-FX Port SwitcHub-2seInstallation Manual Smart Fast Ethernet Switch86$+HDGTXDUWHUV QWHUQDWLRQDO+HDGTXDUWHUVPackage Checklist Package ContentsQuick Installation 6. Verify network communications by ensuring that About this Guide Contents Chapter 2 Setup and ConfigurationChapter 1 Introduction Appendix B Port and Cable Assignments Appendix A TroubleshootingAppendix C Specifications Chapter 3 Hardware ReferenceFast SwitcHub-2se User’s Guide Appendix E Product Support ServicesAppendix D Regulatory Standards Compliance Glossary IndexChapter 1 Introduction Switching TechnologyAccton’s Smart Extender Note The ES3002-TF-SC provides an SC-type fiber connectorThe ES3002-TF-ST provides an ST-type fiber connector Switching Methods Features of the Fast SwitcHub-2se ∙ Transparent bridging function supported Chapter 2 Setup and Configuration Pre-Installation RequirementsConnecting the Switch System Communication Mode in Chapter Making RJ-45 ConnectionsMaking Fiber Optic Connections VariableDescription Page Diagnostic Tests Providing Power to the SwitcHubSetting the Display Mode Filter% ON Selections AvailableUtil% ON Forward% ONFull/Half ON Diag ONVerifying System Operation Verifying Port Status∙ When making a fiber optic connection, be sure the Tx/Rx ports on the switch are attached to the Rx/Tx ports on the other device. Verify that the fiber optic cable snaps into place when attached Front Panel Chapter 3 Hardware ReferenceConfigure Button SmartWatchä Indicator Panel Color For example, if network utilization reaches 1%, the LED labeled 1% will light up. However, if network utilization rises above 35%, the LED labeled 35 and all the other LEDs before it i.e., 1, 5, 10 and 20 will also light up in rapid succession. These indicators monitor the share of valid network frames handled by each port within a 10Mbps or 100Mbps bandwidth, depending on the Ethernet type currently plugged into the back panel. They provide a quick way to monitor the current traffic load relative to the network’s capacity Display Mode LED, indicating that the transmission mode may now Green Green System Diagnostic TestDiag 1,1 1% LED 1,2 5% LEDPort Diagnostic Test Hardware Reference Fast SwitcHub-2se User’s GuideTransmit TX - Indicates outgoing traffic traversing the port Receive RX - Indicates incoming traffic entering the portEthernet Ports Rear Panel3-11 Power SocketFast SwitcHub-2se User’s Guide Hardware ReferenceDiagnosing Switch Indicators Appendix A TroubleshootingPage Switch Integrity ConfigurationFigure B-1 RJ-45 Connector on the Switch Side Appendix BPort and Cable Assignments RJ-45 Port10BASE-T Appendix C SpecificationsProduct Specifications SpecificationsFCC Class B Certification Appendix DRegulatory Standards Compliance EMI WarningRegulatory Standards Compliance Fast SwitcHub-2se User’s GuideThe Interference Handbook Voluntary Control Council for Interference VCCI-2Fast SwitcHub-2se User’s Guide EN55022 Declaration of Conformance CE Mark Declaration of ConformanceRegulatory Standards Compliance Underwriters Laboratories Compliance Statement Safety ComplianceFast SwitcHub-2se User’s Guide Cord Set SpecificationsFast SwitcHub-2se User’s Guide Sicherheitshinweise 9. Bei Störungen des Gerätes den Wartungsdienst verständigenRegulatory Standards Compliance Product Registration Appendix E Product Support ServicesProblem Report Hardware Repair ServiceFast SwitcHub-2se User’s Guide Software Update and Upgrade ServiceBulletin Board Service BBS Interactive Fast Fax U.S.A. officeInternational Headquarters Technical SupportFast SwitcHub-2se User’s Guide Product Support ServicesProduct Support Services Limited WarrantyCustomer Remedies Fast SwitcHub-2se User’s GuideFor warranty information Return ProcessFast SwitcHub-2se User’s Guide Product Support ServicesProduct Support Services Accton OfficesOrdering Information Fast SwitcHub-2se User’s Guide100BASE-TX ConfigurationGlossary 10BASE-TLocal Area Network LAN Daisy-Chain PortEthernet IEEE 802.3 StandardStation Port RJ-45 ConnectorMDI-X Port Medium Dependent Interface - Crossed Shielded Twisted-Pair STPIndex IndexIndex Fast SwitcHub-2se User’s GuideES3002-TF E0596-R01