Manuals / Accton Technology / Computer Equipment / Switch

Accton Technology ES3002-TF Safety Compliance, Fast SwitcHub-2se User’s Guide, Operating Voltage

Models: ES3002-TF

1 58

Download 58 pages 50.96 Kb

Page 45

Safety Compliance

Fast SwitcHub-2se User’s Guide

Safety Compliance

Underwriters Laboratories Compliance Statement

Important! Before making connections, make sure you have the correct Cord Set. Check it (read the label on the cable) against the following specification list.

Operating Voltage

120 Volts

240 Volts (For North America)

240 Volts (For Europe only)

Cord Set Specifications

UL Listed/CSA Certified Cord Set

Minimum 18 AWG

Type SVT or SJT three conductor cord

Maximum length of 15 feet

Parallel blade, grounding type attachment plug rated 15A, 125V

UL Listed/CSA Certified Cord Set

Minimum 18 AWG

Type SVT or SJT three conductor cord

Maximum length of 15 feet

Tandem blade, grounding type attachment plug rated 15A, 125V

Cord Set with H05VV-F cord having three conductors with minimum diameter of 0.75 mm2

IEC-320 receptacle

Male plug rated 6A, 250V

The unit automatically matches the the connected input voltage. Therefore, no additional adjustments are necessary when connecting it to any input voltage within the range marked on the rear panel.

D-4	Regulatory Standards Compliance

Image 45

Accton Technology ES3002-TF Safety Compliance, Fast SwitcHub-2se User’s Guide, Operating Voltage, Cord Set Specifications

Contents

INOGGODJI*IPG SwitcHub-2seInstallation Manual SwitcHub-2seSmart Fast Ethernet Switch with one 10BASE-T/100BASE-TX Port and one 100BASE-FX Port86$+HDGTXDUWHUV QWHUQDWLRQDO+HDGTXDUWHUVPackage Checklist Package ContentsQuick Installation 6. Verify network communications by ensuring that About this Guide Contents Chapter 2 Setup and ConfigurationChapter 1 Introduction Appendix C Specifications Appendix A TroubleshootingChapter 3 Hardware Reference Appendix B Port and Cable AssignmentsAppendix D Regulatory Standards Compliance Appendix E Product Support ServicesGlossary Index Fast SwitcHub-2se User’s GuideChapter 1 Introduction Switching TechnologyAccton’s Smart Extender Note The ES3002-TF-SC provides an SC-type fiber connectorThe ES3002-TF-ST provides an ST-type fiber connector Switching Methods Features of the Fast SwitcHub-2se ∙ Transparent bridging function supported Chapter 2 Setup and Configuration Pre-Installation RequirementsConnecting the Switch System Communication Mode in Chapter Making RJ-45 ConnectionsMaking Fiber Optic Connections VariableDescription Page Diagnostic Tests Providing Power to the SwitcHubSetting the Display Mode Util% ON Selections AvailableForward% ON Filter% ONFull/Half ON Diag ONVerifying System Operation Verifying Port Status∙ When making a fiber optic connection, be sure the Tx/Rx ports on the switch are attached to the Rx/Tx ports on the other device. Verify that the fiber optic cable snaps into place when attached Front Panel Chapter 3 Hardware ReferenceConfigure Button SmartWatchä Indicator Panel Color For example, if network utilization reaches 1%, the LED labeled 1% will light up. However, if network utilization rises above 35%, the LED labeled 35 and all the other LEDs before it i.e., 1, 5, 10 and 20 will also light up in rapid succession. These indicators monitor the share of valid network frames handled by each port within a 10Mbps or 100Mbps bandwidth, depending on the Ethernet type currently plugged into the back panel. They provide a quick way to monitor the current traffic load relative to the network’s capacity Display Mode LED, indicating that the transmission mode may now Diag System Diagnostic Test1,1 1% LED 1,2 5% LED Green GreenPort Diagnostic Test Transmit TX - Indicates outgoing traffic traversing the port Fast SwitcHub-2se User’s GuideReceive RX - Indicates incoming traffic entering the port Hardware ReferenceEthernet Ports Rear PanelFast SwitcHub-2se User’s Guide Power SocketHardware Reference 3-11Diagnosing Switch Indicators Appendix A TroubleshootingPage Switch Integrity ConfigurationPort and Cable Assignments Appendix BRJ-45 Port Figure B-1 RJ-45 Connector on the Switch SideProduct Specifications Appendix C SpecificationsSpecifications 10BASE-TRegulatory Standards Compliance Appendix DEMI Warning FCC Class B CertificationThe Interference Handbook Fast SwitcHub-2se User’s GuideVoluntary Control Council for Interference VCCI-2 Regulatory Standards ComplianceFast SwitcHub-2se User’s Guide EN55022 Declaration of Conformance CE Mark Declaration of ConformanceRegulatory Standards Compliance Fast SwitcHub-2se User’s Guide Safety ComplianceCord Set Specifications Underwriters Laboratories Compliance StatementFast SwitcHub-2se User’s Guide Sicherheitshinweise 9. Bei Störungen des Gerätes den Wartungsdienst verständigenRegulatory Standards Compliance Problem Report Appendix E Product Support ServicesHardware Repair Service Product RegistrationBulletin Board Service BBS Software Update and Upgrade ServiceInteractive Fast Fax U.S.A. office Fast SwitcHub-2se User’s GuideFast SwitcHub-2se User’s Guide Technical SupportProduct Support Services International HeadquartersCustomer Remedies Limited WarrantyFast SwitcHub-2se User’s Guide Product Support ServicesFast SwitcHub-2se User’s Guide Return ProcessProduct Support Services For warranty informationOrdering Information Accton OfficesFast SwitcHub-2se User’s Guide Product Support ServicesGlossary Configuration10BASE-T 100BASE-TXEthernet Daisy-Chain PortIEEE 802.3 Standard Local Area Network LANMDI-X Port Medium Dependent Interface - Crossed RJ-45 ConnectorShielded Twisted-Pair STP Station PortIndex IndexIndex Fast SwitcHub-2se User’s GuideES3002-TF E0596-R01