Manuals / Accton Technology / Computer Equipment / Switch

Accton Technology ES3002-TF Selections Available, Util% ON, Forward% ON, Filter% ON, Coll% ON

Models: ES3002-TF

1 58

Download 58 pages 50.96 Kb

Page 22

Selections Available

Fast SwitcHub-2se User’s Guide

Selections Available

This section shows the information available for each display mode and the corresponding LED indicators. The display functions are listed here in the sequence selected by the configure button. For a more detailed description of these indicators, refer to Chapter 3.

Bandwidth Utilization

Active LED:

Util% (ON)

In this mode, the statistical indicators show the percentage of valid data handled by each port on the switch compared to available bandwidth.

Packet Forwarding Ratio

Active LED:

Forward% (ON)

In this mode, the statistical indicators show the percentage of packets that must be forwarded by bridging hardware to the other port on the switch.

Packet Filtering Ratio

Active LED:

Filter% (ON)

In this mode, the statistical indicators show the percentage of packets that must be filtered from the switch by hardware because the destination address is on the same segment connected to the receiving port (i.e., in the same segment with the source address).

Collision Ratio

Active LED:

Coll% (ON)

In this mode, the statistical indicators show the percentage of packet collisions occurring out of the total packets transmitted by the respective port.

Setup and Configuration

2-7

Image 22

Accton Technology ES3002-TF manual Selections Available, Util% ON, Forward% ON, Filter% ON, Coll% ON

Contents

SwitcHub-2se INOGGODJI*IPGSmart Fast Ethernet Switch SwitcHub-2seInstallation Manual with one 10BASE-T/100BASE-TX Port and one 100BASE-FX PortQWHUQDWLRQDO+HDGTXDUWHUV 86$+HDGTXDUWHUVPackage Contents Package ChecklistQuick Installation 6. Verify network communications by ensuring that About this Guide Chapter 2 Setup and Configuration ContentsChapter 1 Introduction Chapter 3 Hardware Reference Appendix A TroubleshootingAppendix C Specifications Appendix B Port and Cable AssignmentsGlossary Index Appendix E Product Support ServicesAppendix D Regulatory Standards Compliance Fast SwitcHub-2se User’s GuideSwitching Technology Chapter 1 IntroductionNote The ES3002-TF-SC provides an SC-type fiber connector Accton’s Smart ExtenderThe ES3002-TF-ST provides an ST-type fiber connector Switching Methods Features of the Fast SwitcHub-2se ∙ Transparent bridging function supported Pre-Installation Requirements Chapter 2 Setup and ConfigurationConnecting the Switch System Making RJ-45 Connections Communication Mode in ChapterVariable Making Fiber Optic ConnectionsDescription Page Providing Power to the SwitcHub Diagnostic TestsSetting the Display Mode Forward% ON Selections AvailableUtil% ON Filter% ONDiag ON Full/Half ONVerifying Port Status Verifying System Operation∙ When making a fiber optic connection, be sure the Tx/Rx ports on the switch are attached to the Rx/Tx ports on the other device. Verify that the fiber optic cable snaps into place when attached Chapter 3 Hardware Reference Front PanelConfigure Button SmartWatchä Indicator Panel Color For example, if network utilization reaches 1%, the LED labeled 1% will light up. However, if network utilization rises above 35%, the LED labeled 35 and all the other LEDs before it i.e., 1, 5, 10 and 20 will also light up in rapid succession. These indicators monitor the share of valid network frames handled by each port within a 10Mbps or 100Mbps bandwidth, depending on the Ethernet type currently plugged into the back panel. They provide a quick way to monitor the current traffic load relative to the network’s capacity Display Mode LED, indicating that the transmission mode may now 1,1 1% LED 1,2 5% LED System Diagnostic TestDiag Green GreenPort Diagnostic Test Receive RX - Indicates incoming traffic entering the port Fast SwitcHub-2se User’s GuideTransmit TX - Indicates outgoing traffic traversing the port Hardware ReferenceRear Panel Ethernet PortsHardware Reference Power SocketFast SwitcHub-2se User’s Guide 3-11Appendix A Troubleshooting Diagnosing Switch IndicatorsPage Configuration Switch IntegrityRJ-45 Port Appendix BPort and Cable Assignments Figure B-1 RJ-45 Connector on the Switch SideSpecifications Appendix C SpecificationsProduct Specifications 10BASE-TEMI Warning Appendix DRegulatory Standards Compliance FCC Class B CertificationVoluntary Control Council for Interference VCCI-2 Fast SwitcHub-2se User’s GuideThe Interference Handbook Regulatory Standards ComplianceCE Mark Declaration of Conformance Fast SwitcHub-2se User’s Guide EN55022 Declaration of ConformanceRegulatory Standards Compliance Cord Set Specifications Safety ComplianceFast SwitcHub-2se User’s Guide Underwriters Laboratories Compliance Statement9. Bei Störungen des Gerätes den Wartungsdienst verständigen Fast SwitcHub-2se User’s Guide SicherheitshinweiseRegulatory Standards Compliance Hardware Repair Service Appendix E Product Support ServicesProblem Report Product RegistrationInteractive Fast Fax U.S.A. office Software Update and Upgrade ServiceBulletin Board Service BBS Fast SwitcHub-2se User’s GuideProduct Support Services Technical SupportFast SwitcHub-2se User’s Guide International HeadquartersFast SwitcHub-2se User’s Guide Limited WarrantyCustomer Remedies Product Support ServicesProduct Support Services Return ProcessFast SwitcHub-2se User’s Guide For warranty informationFast SwitcHub-2se User’s Guide Accton OfficesOrdering Information Product Support Services10BASE-T ConfigurationGlossary 100BASE-TXIEEE 802.3 Standard Daisy-Chain PortEthernet Local Area Network LANShielded Twisted-Pair STP RJ-45 ConnectorMDI-X Port Medium Dependent Interface - Crossed Station PortIndex IndexFast SwitcHub-2se User’s Guide IndexES3002-TF E0596-R01