Manuals / Accton Technology / Computer Equipment / Switch

Accton Technology ES3002-TF manual About this Guide

Models: ES3002-TF

1 58

Download 58 pages 50.96 Kb

Page 7

About this Guide

About this Guide

This guide is designed for the experienced network installer. It describes how to install and operate Accton’s Fast SwitcHub-2se Ethernet switch. After reading this manual, you should be able to use the front display panel and configure options to manage all your network connections.

This manual covers the following topics:

Chapter 1 - Product Overview

Brief description of switching technology, followed by a description of this switch and a summary of its important features and specifications.

Chapter 2 - Setup and Configuration

Installing a Fast SwitcHub-2se and making basic network connections. Shows sample network configurations for a local area network.

Chapter 3 - Hardware Reference

Detailed description of indicator panel and ports.

Appendices - Troubleshooting, cable assignments, and product specifications.

About this Guide

v

Image 7

Accton Technology ES3002-TF manual About this Guide

Contents

INOGGODJI*IPG SwitcHub-2sewith one 10BASE-T/100BASE-TX Port and one 100BASE-FX Port SwitcHub-2seInstallation Manual Smart Fast Ethernet Switch86$+HDGTXDUWHUV QWHUQDWLRQDO+HDGTXDUWHUVPackage Checklist Package ContentsQuick Installation 6. Verify network communications by ensuring that About this Guide Chapter 2 Setup and Configuration ContentsChapter 1 Introduction Appendix B Port and Cable Assignments Appendix A TroubleshootingAppendix C Specifications Chapter 3 Hardware ReferenceFast SwitcHub-2se User’s Guide Appendix E Product Support ServicesAppendix D Regulatory Standards Compliance Glossary IndexChapter 1 Introduction Switching TechnologyNote The ES3002-TF-SC provides an SC-type fiber connector Accton’s Smart ExtenderThe ES3002-TF-ST provides an ST-type fiber connector Switching Methods Features of the Fast SwitcHub-2se ∙ Transparent bridging function supported Pre-Installation Requirements Chapter 2 Setup and ConfigurationConnecting the Switch System Communication Mode in Chapter Making RJ-45 ConnectionsVariable Making Fiber Optic ConnectionsDescription Page Diagnostic Tests Providing Power to the SwitcHubSetting the Display Mode Filter% ON Selections AvailableUtil% ON Forward% ONFull/Half ON Diag ONVerifying System Operation Verifying Port Status∙ When making a fiber optic connection, be sure the Tx/Rx ports on the switch are attached to the Rx/Tx ports on the other device. Verify that the fiber optic cable snaps into place when attached Front Panel Chapter 3 Hardware ReferenceConfigure Button SmartWatchä Indicator Panel Color For example, if network utilization reaches 1%, the LED labeled 1% will light up. However, if network utilization rises above 35%, the LED labeled 35 and all the other LEDs before it i.e., 1, 5, 10 and 20 will also light up in rapid succession. These indicators monitor the share of valid network frames handled by each port within a 10Mbps or 100Mbps bandwidth, depending on the Ethernet type currently plugged into the back panel. They provide a quick way to monitor the current traffic load relative to the network’s capacity Display Mode LED, indicating that the transmission mode may now Green Green System Diagnostic TestDiag 1,1 1% LED 1,2 5% LEDPort Diagnostic Test Hardware Reference Fast SwitcHub-2se User’s GuideTransmit TX - Indicates outgoing traffic traversing the port Receive RX - Indicates incoming traffic entering the portEthernet Ports Rear Panel3-11 Power SocketFast SwitcHub-2se User’s Guide Hardware ReferenceDiagnosing Switch Indicators Appendix A TroubleshootingPage Switch Integrity ConfigurationFigure B-1 RJ-45 Connector on the Switch Side Appendix BPort and Cable Assignments RJ-45 Port10BASE-T Appendix C SpecificationsProduct Specifications SpecificationsFCC Class B Certification Appendix DRegulatory Standards Compliance EMI WarningRegulatory Standards Compliance Fast SwitcHub-2se User’s GuideThe Interference Handbook Voluntary Control Council for Interference VCCI-2CE Mark Declaration of Conformance Fast SwitcHub-2se User’s Guide EN55022 Declaration of ConformanceRegulatory Standards Compliance Underwriters Laboratories Compliance Statement Safety ComplianceFast SwitcHub-2se User’s Guide Cord Set Specifications9. Bei Störungen des Gerätes den Wartungsdienst verständigen Fast SwitcHub-2se User’s Guide SicherheitshinweiseRegulatory Standards Compliance Product Registration Appendix E Product Support ServicesProblem Report Hardware Repair ServiceFast SwitcHub-2se User’s Guide Software Update and Upgrade ServiceBulletin Board Service BBS Interactive Fast Fax U.S.A. officeInternational Headquarters Technical SupportFast SwitcHub-2se User’s Guide Product Support ServicesProduct Support Services Limited WarrantyCustomer Remedies Fast SwitcHub-2se User’s GuideFor warranty information Return ProcessFast SwitcHub-2se User’s Guide Product Support ServicesProduct Support Services Accton OfficesOrdering Information Fast SwitcHub-2se User’s Guide100BASE-TX ConfigurationGlossary 10BASE-TLocal Area Network LAN Daisy-Chain PortEthernet IEEE 802.3 StandardStation Port RJ-45 ConnectorMDI-X Port Medium Dependent Interface - Crossed Shielded Twisted-Pair STPIndex IndexIndex Fast SwitcHub-2se User’s GuideES3002-TF E0596-R01