ADT Security Services ADT-UDACT Table 3-7: Ademco Contact ID, Secondary Number

Document 50934 Rev B 5/15/00 PN 50934:B 29

Ademco Contact ID Format

If 'E' is entered for address 42, the following data is automatically programmed for the Secondary

phone number event codes. Enter a '000' for the data setting to disable the report.

Address Description Setting 1 Group # 6 Sensor No.

139 - 141 Secondary # General Alarm Code 110 00 000 2

142 - 144 Secondary # Zone/Point Alarm Code 110 4 00 Note 3

145 - 147 Secondary # General Supervisory Code 200 00 000 2

148 - 150 Secondary # Zone/Point Supervisory Code 200 00 Note 3

151 - 153 Secondary # General Fault Code 300 00

154 - 156 Secondary # AC Fault Code 301 00

157 - 159 Secondary # Zone/Point Fault Code 380 00 Note 3

160 - 162 Secondary # Low Battery Fault Code 302 00

163 - 165 Secondary # Telco Primary Line Fault Code 351 00

166 - 168 Secondary # Telco Secondary Line Fault Code 352 00

169 - 171 Secondary # NAC Fault Code 321 00

172 - 174 Secondary # Comm. Trouble Primary # Code 354 00

175 - 177 Secondary # Comm. Trouble Secondary # Code 354 00

178 - 180 Secondary # 485 Comm. Trouble Code 300 00

181 - 183 Secondary # System Off Normal Code 308 00

184 - 186 Secondary # ADT-UDACT Off Normal Code 350 00

187 - 189 Secondary # System 24 Hour Test 602 00

190 - 192 Secondary # System 24 Hour Test w/active event 608 00

193 - 195 Secondary # Manual Test Message 601 00

Notes: 1) Note: Zero entries prevent the transmission of the report to the Central Station.

2) Refer to Contact ID program locations 64 - 68.

3) The identification of the zone/device number is automatically transmitted by the ADT-UDACT and is

added to the main event code. See Table 5-3 for more information.

4) For control panels Unimode 2020/1010, ADT-MNNA, and Unimode 300/400 the factory default event

code is 110 and reprogrammable. The Unimode 300 and Unimode 400 are unique in point reporting

mode in that only the control module report codes are programmable. The factory setting of report

code 111 is fixed for addressable smoke detectors and cannot be changed.

5) The Group # is automatically incremented for Unimode 2020/1010 and ADT-MNNA applications.

Table 3-7: Ademco Contact ID, Secondary Number

Contents

Main The ADT-UDACT Heat detectors are designed to protect property, not life. While a fire alarm system may lower insurance rates, it is not a substitute for fire insurance! Fire Alarm System Limitations Several different sources of power can be con- nected to the fire alarm control panel. FCC Warning System Reacceptance Test after Software Changes. Adherence to the following will aid in problem-free installation with long-term reliability: Installation Precautions Page Table of Contents Before proceeding, the installer should be familiar with the following documents. 1.0 Product Description 1.1 Product Features Figure 1-1: ADT-UDACT Assembly 1.2 Controls and Indicators Figure 1-2: Controls and Indicators 1.3 Compatible Panels 1.4 Digital Communicator 1.5 Circuits 1.6 Optional Device 1.7 Specifications 1.8 Telephone Requirements and Warnings 1.9 Modes and Special Functions Page Figure 2-1: Wiring Phone Jacks 2.2 Output Circuits 2.1 General 2.0 Installation and Wiring Figure 2-2: Relay Driver Connections Figure 2-3: Monitoring for ADT-UDACT Trouble Page 3.0 Programming Instructions Programming Mode 3.1 Entering Program Mode The Function of each switch in program mode is shown below: { Figure 3-1: ADT-UDACT Keypad Primary phone number. (00-15) 48 47 161 FFFFFFFFF 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15. FFFFFFFFFFFFFFFF 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41. Page Table 3-1: Start and End Monitoring Addresses Page Table 3-2: Event Codes, Primary Number 4+2 Standard and 4+2 Express Formats Table 3-3: Event Codes, Primary Number Address Description Setting 1 Group # 6 Sensor No. Table 3-4: Ademco Contact ID, Primary Number Ademco Contact ID Format Table 3-5: Event Codes, Secondary Number 4+2 Standard and 4+2 Express Formats I Table 3-6: Event Codes, Secondary Number Ademco Contact ID Format Table 3-7: Ademco Contact ID, Secondary Number Address Description Setting 1 Group # 6 Sensor No. 4.0 Operating Instructions 4.1 Normal Mode Page Figure 4-1: ADT-UDACT Phone Connectors and LEDs Page 4.2 Type Mode Page 4.3 Troubleshoot Mode Page 5.0 Reporting Formats Table 5-1: Data Reporting Structure Table 5-2: Letter Code Definitions (Refer to Table 5-1) Table 5-3: Ademco Contact ID Reporting Structure Page 6.0 Compatible Receivers Table 6-1: Compatible UL Listed Receivers 7.0 Programming Reference Sheets 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 Enter military time (i.e. 1400 for 2 PM) 16 Enter 0 - F. Programming Reference Sheet Programming Reference Sheet Factory Default Settings 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 (4+2 Standard 1800/2300). 17 18 19 20 Primary Account Code. 21 22 23 24 0000 = 12:00 midnight. Programming Reference Sheet Factory Default Appendix A: Zone Assignments (Unimode 300/400) Zone No. Zone Function Zone No. Zone Function Zone No. Zone Function Appendix B: Point Assignments (Unimode 300*/400) Appendix B (continued): Point Assignments (Unimode 300*/400) Appendix B (continued): Point Assignments (Unimode 300*/400) Note: Event Code cannot be altered. Physical location is critical to the point number reported. Appendix C: Point Assignments (ADT-MNNA) Page Page Page Page Appendix D: Unimode 2020/1010 Figure D-2: ADT-UDACT Mounting in CHS-4 Figure D-1: ADT-UBS-1F SIB Figure D-3: EIA-485 Connection to Panel Mounted ADT-UDACT ADT-UDACT Figure D-4: EIA-485 Connection to Remote ADT-UDACT Figure E-2: ADT-CPU-400 Module Appendix E: Unimode 300/400 Figure E-1: ADT-ABS8RF Figure E-3: Unimode 400 External ADT-UDACT Mounting in ADT-ABS8RF Type Mode Programming Event Code/Report Transmission via Ademco Contact ID Format Only ADT-CAB - B3 ADT-CAB - C3 ADT-CAB - 400AA Appendix F: ADT-MNNA ADT-MNNA Figure F-1: EIA-485 Connection to Panel Mounted ADT-UDACT ADT-UDACT Figure F-2: EIA-485 Connection to Remote ADT-UDACT Appendix G: Annunciators