ADT Security Services ADT-UDACT

Document 50934 Rev B 5/15/00 PN 50934:B

Point No. Point Function Point No. Point Function Point No. Point Function

121 161 201

122 162 202

123 163 203

124 164 204

125 165 205

126 166 206

127 167 207

128 168 208

129 169 209

130 170 210

131 171 211

132 172 212

133 173 213

134 174 214

135 175 215

136 176 216

137 177 217

138 178 218

139 179 219

140 180 220

141 181 221

142 182 222

143 183 223

144 184 224

145 185 225

146 186 226

147 187 227

148 188 228

149 189 229

150 190 230

151 191 231

152 192 232

153 193 233

154 194 234

155 195 235

156 196 236

157 197 237

158 198 238

159 199 239

160 200 240

Appendix C (continued): Point Assignments (ADT-MNNA)

Contents

Main The ADT-UDACT Heat detectors are designed to protect property, not life. While a fire alarm system may lower insurance rates, it is not a substitute for fire insurance! Fire Alarm System Limitations Several different sources of power can be con- nected to the fire alarm control panel. FCC Warning System Reacceptance Test after Software Changes. Adherence to the following will aid in problem-free installation with long-term reliability: Installation Precautions Page Table of Contents Before proceeding, the installer should be familiar with the following documents. 1.0 Product Description 1.1 Product Features Figure 1-1: ADT-UDACT Assembly 1.2 Controls and Indicators Figure 1-2: Controls and Indicators 1.3 Compatible Panels 1.4 Digital Communicator 1.5 Circuits 1.6 Optional Device 1.7 Specifications 1.8 Telephone Requirements and Warnings 1.9 Modes and Special Functions Page Figure 2-1: Wiring Phone Jacks 2.2 Output Circuits 2.1 General 2.0 Installation and Wiring Figure 2-2: Relay Driver Connections Figure 2-3: Monitoring for ADT-UDACT Trouble Page 3.0 Programming Instructions Programming Mode 3.1 Entering Program Mode The Function of each switch in program mode is shown below: { Figure 3-1: ADT-UDACT Keypad Primary phone number. (00-15) 48 47 161 FFFFFFFFF 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15. FFFFFFFFFFFFFFFF 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41. Page Table 3-1: Start and End Monitoring Addresses Page Table 3-2: Event Codes, Primary Number 4+2 Standard and 4+2 Express Formats Table 3-3: Event Codes, Primary Number Address Description Setting 1 Group # 6 Sensor No. Table 3-4: Ademco Contact ID, Primary Number Ademco Contact ID Format Table 3-5: Event Codes, Secondary Number 4+2 Standard and 4+2 Express Formats I Table 3-6: Event Codes, Secondary Number Ademco Contact ID Format Table 3-7: Ademco Contact ID, Secondary Number Address Description Setting 1 Group # 6 Sensor No. 4.0 Operating Instructions 4.1 Normal Mode Page Figure 4-1: ADT-UDACT Phone Connectors and LEDs Page 4.2 Type Mode Page 4.3 Troubleshoot Mode Page 5.0 Reporting Formats Table 5-1: Data Reporting Structure Table 5-2: Letter Code Definitions (Refer to Table 5-1) Table 5-3: Ademco Contact ID Reporting Structure Page 6.0 Compatible Receivers Table 6-1: Compatible UL Listed Receivers 7.0 Programming Reference Sheets 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 Enter military time (i.e. 1400 for 2 PM) 16 Enter 0 - F. Programming Reference Sheet Programming Reference Sheet Factory Default Settings 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 (4+2 Standard 1800/2300). 17 18 19 20 Primary Account Code. 21 22 23 24 0000 = 12:00 midnight. Programming Reference Sheet Factory Default Appendix A: Zone Assignments (Unimode 300/400) Zone No. Zone Function Zone No. Zone Function Zone No. Zone Function Appendix B: Point Assignments (Unimode 300*/400) Appendix B (continued): Point Assignments (Unimode 300*/400) Appendix B (continued): Point Assignments (Unimode 300*/400) Note: Event Code cannot be altered. Physical location is critical to the point number reported. Appendix C: Point Assignments (ADT-MNNA) Page Page Page Page Appendix D: Unimode 2020/1010 Figure D-2: ADT-UDACT Mounting in CHS-4 Figure D-1: ADT-UBS-1F SIB Figure D-3: EIA-485 Connection to Panel Mounted ADT-UDACT ADT-UDACT Figure D-4: EIA-485 Connection to Remote ADT-UDACT Figure E-2: ADT-CPU-400 Module Appendix E: Unimode 300/400 Figure E-1: ADT-ABS8RF Figure E-3: Unimode 400 External ADT-UDACT Mounting in ADT-ABS8RF Type Mode Programming Event Code/Report Transmission via Ademco Contact ID Format Only ADT-CAB - B3 ADT-CAB - C3 ADT-CAB - 400AA Appendix F: ADT-MNNA ADT-MNNA Figure F-1: EIA-485 Connection to Panel Mounted ADT-UDACT ADT-UDACT Figure F-2: EIA-485 Connection to Remote ADT-UDACT Appendix G: Annunciators