ADT Security Services ADT-UDACT Appendix B: Point Assignments (Unimode 300*/400)

Document 50934 Rev B 5/15/00 PN 50934:B

48

Appendix B: Point Assignments (Unimode 300*/400)

.oNtnioPeciveDfoepyT pooLseludoM()1

.oNtnioPeciveDfoepyT pooLseludoM()1

.oNtnioPeciveDfoepyT pooLseludoM()2

.oNtnioPeciveDfoepyT pooLseludoM()2

100150101151

200250201251

300350301351

400450401451

500550501551

600650601651

700750701751

800850801851

900950901951

010060011061

110160111161

210260211261

310360311361

410460411461

510560511561

610660611661

710760711761

810860811861

910960911961

020070021071

120170121171

220270221271

320370321371

420470421471

520570521571

620670621671

720770721771

820870821871

920970921971

030080031081

130180131181

230280231281

330380331381

430480431481

530580531581

630680631681

730780731781

830880831881

930980931981

040090041091

140190141191

240290241291

340390341391

440490441491

540590541591

640690641691

740790

toNoD margorP

741791

toNoD margorP

840890841891

940990941991

050001051002

Note: Use chart to carefully identify all points in the system. Take special precaution with any supervisory points and remote

switches in the system. Use Type Mode (refer to Section 4.2 Type Mode) to match the function of remaining points in the system

for proper reporting. *For Unimode 300, use only Loop 1 in the chart.

Contents

Main The ADT-UDACT Heat detectors are designed to protect property, not life. While a fire alarm system may lower insurance rates, it is not a substitute for fire insurance! Fire Alarm System Limitations Several different sources of power can be con- nected to the fire alarm control panel. FCC Warning System Reacceptance Test after Software Changes. Adherence to the following will aid in problem-free installation with long-term reliability: Installation Precautions Page Table of Contents Before proceeding, the installer should be familiar with the following documents. 1.0 Product Description 1.1 Product Features Figure 1-1: ADT-UDACT Assembly 1.2 Controls and Indicators Figure 1-2: Controls and Indicators 1.3 Compatible Panels 1.4 Digital Communicator 1.5 Circuits 1.6 Optional Device 1.7 Specifications 1.8 Telephone Requirements and Warnings 1.9 Modes and Special Functions Page Figure 2-1: Wiring Phone Jacks 2.2 Output Circuits 2.1 General 2.0 Installation and Wiring Figure 2-2: Relay Driver Connections Figure 2-3: Monitoring for ADT-UDACT Trouble Page 3.0 Programming Instructions Programming Mode 3.1 Entering Program Mode The Function of each switch in program mode is shown below: { Figure 3-1: ADT-UDACT Keypad Primary phone number. (00-15) 48 47 161 FFFFFFFFF 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15. FFFFFFFFFFFFFFFF 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41. Page Table 3-1: Start and End Monitoring Addresses Page Table 3-2: Event Codes, Primary Number 4+2 Standard and 4+2 Express Formats Table 3-3: Event Codes, Primary Number Address Description Setting 1 Group # 6 Sensor No. Table 3-4: Ademco Contact ID, Primary Number Ademco Contact ID Format Table 3-5: Event Codes, Secondary Number 4+2 Standard and 4+2 Express Formats I Table 3-6: Event Codes, Secondary Number Ademco Contact ID Format Table 3-7: Ademco Contact ID, Secondary Number Address Description Setting 1 Group # 6 Sensor No. 4.0 Operating Instructions 4.1 Normal Mode Page Figure 4-1: ADT-UDACT Phone Connectors and LEDs Page 4.2 Type Mode Page 4.3 Troubleshoot Mode Page 5.0 Reporting Formats Table 5-1: Data Reporting Structure Table 5-2: Letter Code Definitions (Refer to Table 5-1) Table 5-3: Ademco Contact ID Reporting Structure Page 6.0 Compatible Receivers Table 6-1: Compatible UL Listed Receivers 7.0 Programming Reference Sheets 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 Enter military time (i.e. 1400 for 2 PM) 16 Enter 0 - F. Programming Reference Sheet Programming Reference Sheet Factory Default Settings 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 (4+2 Standard 1800/2300). 17 18 19 20 Primary Account Code. 21 22 23 24 0000 = 12:00 midnight. Programming Reference Sheet Factory Default Appendix A: Zone Assignments (Unimode 300/400) Zone No. Zone Function Zone No. Zone Function Zone No. Zone Function Appendix B: Point Assignments (Unimode 300*/400) Appendix B (continued): Point Assignments (Unimode 300*/400) Appendix B (continued): Point Assignments (Unimode 300*/400) Note: Event Code cannot be altered. Physical location is critical to the point number reported. Appendix C: Point Assignments (ADT-MNNA) Page Page Page Page Appendix D: Unimode 2020/1010 Figure D-2: ADT-UDACT Mounting in CHS-4 Figure D-1: ADT-UBS-1F SIB Figure D-3: EIA-485 Connection to Panel Mounted ADT-UDACT ADT-UDACT Figure D-4: EIA-485 Connection to Remote ADT-UDACT Figure E-2: ADT-CPU-400 Module Appendix E: Unimode 300/400 Figure E-1: ADT-ABS8RF Figure E-3: Unimode 400 External ADT-UDACT Mounting in ADT-ABS8RF Type Mode Programming Event Code/Report Transmission via Ademco Contact ID Format Only ADT-CAB - B3 ADT-CAB - C3 ADT-CAB - 400AA Appendix F: ADT-MNNA ADT-MNNA Figure F-1: EIA-485 Connection to Panel Mounted ADT-UDACT ADT-UDACT Figure F-2: EIA-485 Connection to Remote ADT-UDACT Appendix G: Annunciators