ADT Security Services ADT-UDACT Appendix E: Unimode 300/400

Document 50934 Rev B 5/15/00 PN 50934:B 59

Figure E-2: ADT-CPU-400 Module

The ADT-UDACT is capable of reporting a maximum of 99

zones or 448 points when used with the Unimode 400.

The ADT-UDACT must be mounted remotely in an ADT-ABS8RF

or ADT-UBS-1 enclosure up to 6000 feet away from the control

panel. All power must be removed from the Control Panel before

making any connections to prevent circuit damage. The EIA-485

serial interface is connected between the Control Panel and ADT-

UDACT using twisted, shielded pair wire. Power should be wired

from the MPS-400 24 VDC nonresettable output to TB1 on the

ADT-UDACT.

Remove all power from the control panel by disconnecting AC and

batteries. Since the Unimode 400 cannot accommodate the ADT-

UDACT in the control panel enclosure, the ADT-UDACT must

be mounted remotely using an ADT-ABS8RF enclosure. Ferrite

cores are recommended for this application. Refer to Figure E-3

and the accompanying notes for wiring alternatives.

Connect the communication line between the EIA-485 terminal block TB4 on the

Unimode 300/400 and TB-1 terminals 3 and 4 on the ADT-UDACT, being certain to

observe polarity (refer to Figure E-3). Recommended wire is 12 AWG to 18 AWG twisted

pair. If no other devices are connected to the EIA-485, install a 120 ohm EOL resistor

across ADT-UDACT TB1 terminals 3 and 4.

Connect the supplied ground strap from the ADT-UDACT Earth Ground terminal on

TB3 to a solid building earth ground. Connect 24VDC nonresettable power to TB-1

terminals 1 and 2 on the ADT-UDACT (refer to Figure E-3).

SYSTEM

RESET LAMP

TEST

SYSTEM

TROUBLE DISABLED

POINTS ALARM

SILENCED

SUPERVISORY

SIGNAL

Appendix E: Unimode 300/400

ABS-8R.WMF

Figure E-1:

ADT-ABS8RF

ABS-8R.WMF

Contents

Main The ADT-UDACT Heat detectors are designed to protect property, not life. While a fire alarm system may lower insurance rates, it is not a substitute for fire insurance! Fire Alarm System Limitations Several different sources of power can be con- nected to the fire alarm control panel. FCC Warning System Reacceptance Test after Software Changes. Adherence to the following will aid in problem-free installation with long-term reliability: Installation Precautions Page Table of Contents Before proceeding, the installer should be familiar with the following documents. 1.0 Product Description 1.1 Product Features Figure 1-1: ADT-UDACT Assembly 1.2 Controls and Indicators Figure 1-2: Controls and Indicators 1.3 Compatible Panels 1.4 Digital Communicator 1.5 Circuits 1.6 Optional Device 1.7 Specifications 1.8 Telephone Requirements and Warnings 1.9 Modes and Special Functions Page Figure 2-1: Wiring Phone Jacks 2.2 Output Circuits 2.1 General 2.0 Installation and Wiring Figure 2-2: Relay Driver Connections Figure 2-3: Monitoring for ADT-UDACT Trouble Page 3.0 Programming Instructions Programming Mode 3.1 Entering Program Mode The Function of each switch in program mode is shown below: { Figure 3-1: ADT-UDACT Keypad Primary phone number. (00-15) 48 47 161 FFFFFFFFF 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15. FFFFFFFFFFFFFFFF 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41. Page Table 3-1: Start and End Monitoring Addresses Page Table 3-2: Event Codes, Primary Number 4+2 Standard and 4+2 Express Formats Table 3-3: Event Codes, Primary Number Address Description Setting 1 Group # 6 Sensor No. Table 3-4: Ademco Contact ID, Primary Number Ademco Contact ID Format Table 3-5: Event Codes, Secondary Number 4+2 Standard and 4+2 Express Formats I Table 3-6: Event Codes, Secondary Number Ademco Contact ID Format Table 3-7: Ademco Contact ID, Secondary Number Address Description Setting 1 Group # 6 Sensor No. 4.0 Operating Instructions 4.1 Normal Mode Page Figure 4-1: ADT-UDACT Phone Connectors and LEDs Page 4.2 Type Mode Page 4.3 Troubleshoot Mode Page 5.0 Reporting Formats Table 5-1: Data Reporting Structure Table 5-2: Letter Code Definitions (Refer to Table 5-1) Table 5-3: Ademco Contact ID Reporting Structure Page 6.0 Compatible Receivers Table 6-1: Compatible UL Listed Receivers 7.0 Programming Reference Sheets 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 Enter military time (i.e. 1400 for 2 PM) 16 Enter 0 - F. Programming Reference Sheet Programming Reference Sheet Factory Default Settings 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 (4+2 Standard 1800/2300). 17 18 19 20 Primary Account Code. 21 22 23 24 0000 = 12:00 midnight. Programming Reference Sheet Factory Default Appendix A: Zone Assignments (Unimode 300/400) Zone No. Zone Function Zone No. Zone Function Zone No. Zone Function Appendix B: Point Assignments (Unimode 300*/400) Appendix B (continued): Point Assignments (Unimode 300*/400) Appendix B (continued): Point Assignments (Unimode 300*/400) Note: Event Code cannot be altered. Physical location is critical to the point number reported. Appendix C: Point Assignments (ADT-MNNA) Page Page Page Page Appendix D: Unimode 2020/1010 Figure D-2: ADT-UDACT Mounting in CHS-4 Figure D-1: ADT-UBS-1F SIB Figure D-3: EIA-485 Connection to Panel Mounted ADT-UDACT ADT-UDACT Figure D-4: EIA-485 Connection to Remote ADT-UDACT Figure E-2: ADT-CPU-400 Module Appendix E: Unimode 300/400 Figure E-1: ADT-ABS8RF Figure E-3: Unimode 400 External ADT-UDACT Mounting in ADT-ABS8RF Type Mode Programming Event Code/Report Transmission via Ademco Contact ID Format Only ADT-CAB - B3 ADT-CAB - C3 ADT-CAB - 400AA Appendix F: ADT-MNNA ADT-MNNA Figure F-1: EIA-485 Connection to Panel Mounted ADT-UDACT ADT-UDACT Figure F-2: EIA-485 Connection to Remote ADT-UDACT Appendix G: Annunciators