Advantech PCI-1710 3.1 Overview, 3.2 I/O Connector

14 PCI-1710/1710HG User's Manual

3.1 Overview

Correct signal connections are one of the most important factors in

ensuring that your application system is sending and receiving data

correctly. A good signal connection can avoid much unnecessary and

costly damage to your valuable PC and other hardware devices. This

chapter will provide some useful information about how to connect

input and output signals to the PCI-1710/1710HG card via the I/O

connector.

3.2 I/O Connector

The I/O connector for the PCI-1710/1710HG card has 68 pins that you

can connect to 68-pin accessories with the PCL-10168 shielded cable.

Note! The PCL-10168 shielded cable is specially designed

for the PCI-1710/1710HG for reducing noise in the

analog signal lines. Its wires are all twisted pairs,

and the analog lines and digital lines are seperately

shielded, providing minimal cross talk between

signals and the best protection against EMI/EMC

problems.

Pin Assignment

Figure 3-1 shows the pin assignments for the 68-pin I/O connector on

the PCI-1710/1710HG card.

Contents

Main Page Contents Chapter 5: Calibration............................................ 4 5 Appendix A: 82C54 Counter Chip Functions ...... 5 1 Page 1.1 Introduction PCI-bus Plug and Play Flexible Inputs Types and Ranges Setting On-board FIFO (First In First Out) Memory On-board Programmable Counter 1.2 Features 1.3 Specifications Analog Input: Page Analog Output: Digital Input: Digital Output: Programmable Timer/Counter General: 8PCI-1710 /1710HG User's Manual 1.4 Block Diagram Figure 1-1: PCI-1710/PCI-1710HG block diagram Page 2.1 Initial Inspection 2.2 Unpacking 2.3 Installation Instructions Page Page 3.1 Overview 3.2 I/O Connector Pin Assignment Figure 3-1: I/O connector pin assignments for the PCI-1710/1710 HG card Chapter 3 Signal Connections 15 16 PCI-1710/1710HG User's Manual I/O Connector Signal Descriptions Chapter 3 Signal Connections 17 I/O Connector Signal Descriptions (part II) 18 PCI-1710/1710HG User's Manual I/O Connector Signal Descriptions (part III) 3.3 Analog Input Connections Single-ended Channel Connections Differential Channel Connections ExternalInternal Page Page 3.4 Analog Output Connections 3.5 Trigger Source Connections Internal Pacer Trigger Connection External Trigger Source Connection 3.6 Field Wiring Considerations Page Page 4.1 Overview 4.2 I/O Port Address Map Chapter 4 Register Structure and Format 29 Table 4-1: PCI-1710/1710HG register format (Part 1) Table 4-1: PCI-1710/1710HG register format (Part 2) 30 PCI-1710/1710HG User's Manual Table 4-1: PCI-1710/1710HG register format (Part 3) Chapter 4 Register Structure and Format 31 Table 4-1: PCI-1710/1710HG register format (Part 4) 32 PCI-1710/1710HG User's Manual 4.3 Channel Number and A/D Data BASE+0 and BASE+1 4.4 Software A/D Trigger BASE+0 4.5 A/D Channel Range Setting BASE+2 PCI-1710 The following table lists the gain codes for the PCI-1710: PCI-1710HG 4.6 MUX ControlBASE+4 and BASE+5 Page 4.7 Control Register BASE+6 4.8 Status Register BASE+6 and BASE+7 4.9 Clear Interrupt and FIFO BASE+8 and BASE+9 Page 4.12 D/A Reference Control BASE+14 Page Page 5.1 Introduction 5.2 VR Assignment 5.3 A/D Calibration 5.4 D/A Calibration 5.5 Self A/D Calibration Page Page A.1 The Intel 82C54 Counter 0 Counter 1 & 2 A.2 Counter Read/Write and Control Registers Description: Page Page A.3 Counter Operating Modes MODE 0 Stop on Terminal Count MODE 1 Programmable One-shot Pulse MODE 2 Rate Generator MODE 3 Square Wave Generator MODE 4 Software-Triggered Strobe MODE 5 Hardware-Triggered Strobe A.4 Counter Operations Read/Write Operation Counter Read-back Command Counter Latch Operation