Manuals / Agilent Technologies / Lawn and Garden / Portable Generator

Agilent Technologies 664xA, 665xA, 667xA, 669xA, 668xA manual Meaning and Type, Description

Models: 668xA 669xA 667xA 664xA 665xA

1 70

Download 70 pages 51.66 Kb

Page 31

*RST

Meaning and Type

Reset Device State

Description

This command resets the power supply to a factory-defined state as defined below. *RST also forces an ABORt command.

	Command	State
	CAL:STAT OFF	OUTP[:STAT] OFF
CURR[:LEV][:IMM] *		OUTP:PROT:DEL *
CURR[:LEV]:TRIG *		OUTP:REL[:STAT] OFF
CURR:PROT:STAT OFF		OUTP:REL:POL NORM
DIG:DATA 0		TRIG:SOUR BUS
DISP[:WIND]:STAT ON		VOLT[:LEV][:IMM] *
DISP[:WIND]:MODE NORM		VOLT[:LEV][:TRIG] *
DISP[:WIND]:TEXT		VOLT:PROT[:LEV] *

INIT:CONT OFF

* Model-dependent value. See Table 3-1.

Command Syntax	*RST
Parameters	(None)
Query Syntax	(None)
Related Commands	*PSC	*SAV

*SAV

Meaning and Type

SAVE Device State

Description

This command stores the present state of the power supply to the specified location in memory. Up to four states can be stored. Under certain conditions (see "Turn-On Conditions" in "Chapter 5 - Front Panel Operation" of the Operating Guide), location 0 may hold the device state that is automatically recalled at power turn-on.

The following power supply parameters are stored by *SAV:

CURR[:LEV][:IMM]	OUTP[:STAT]	OUTP:REL:POL
CURR:PROT:STAT	OUTP:PROT:DEL	VOLT[:LEV][:IMM]
DIG:DATA[:VAL]	OUTP:REL[:STAT]	VOLT:PROT[:LEV]
Command Syntax	*SAV <NRf>
Parameters	0123
Example	SAV 3
Query Syntax	(None)
Related Commands	RCL RST

The power supply uses nonvolatile memory for recording register states. Programs that repeatedly use *SAV for recalling states cause frequent write cycles to the memory and can eventually exceed the maximum number of write cycles for the memory (see in the power supply Operating Guide).

Language Dictionary 31

Image 31

Agilent Technologies 664xA, 665xA, 667xA, 669xA, 668xA manual Meaning and Type, Description

Contents

Microfiche Part No PROGRAMMING GUIDE GPIB DC POWER SUPPLIESAgilent Technologies Models 664xA, 665xA, 667xA, 668xA, and 669xA Agilent Part NoPrinting History Safety GuidelinesLANGUAGE DICTIONARY ContentsGENERAL INFORMATION REMOTE PROGRAMMINGDisplay Subsystem Description of Subsystem CommandsSystem Commands Current SubsystemCOMPATIBILITY LANGUAGE ERROR MESSAGESSTATUS REPORTING SCPI CONFORMANCE INFORMATIONPage User’s Guide General InformationAbout this Guide Documentation SummaryAccessing Online Help Prerequisites for Using this GuideVXIplug&play Power Product Instrument Drivers Downloading and Installing the DriverConventions GPIB Capabilities Of The Power SupplyRemote Programming Introduction To SCPISCPI Messages Types of SCPI CommandsCommon Commands Subsystem CommandsExample Figure 2-1. Command Message StructureParts of a SCPI Message Message ComponentRoot Specifier Traversing the Command TreeQuery Indicator Message Unit SeparatorOUTPUTPROTECTIONCLEAR STATUSOPERATIONCONDITION? Figure 2-2. Partial Command Tree Active Header PathThe Effect of Optional Headers Moving Among SubsystemsValue Coupling Including Common CommandsSymbol SCPI QueriesTable 2-2. Suffixes and Multipliers Examplescontrolled GPIB interfaces Listening FormatsProgramming Voltage and Current Disable the outputEnable the output Controlling the OutputWriting to the Display Saving and Recalling StatesProgramming Status Programming the Digital I/O Port System ConsiderationsThe GPIB Address A direct primary address and a secondary address A stand-alone primary address and a direct primary addressAssigning the GPIB Address In Programs Sample Program Code Error HandlingDOS Drivers Agilent BASIC ControllersController Using Agilent 82335A Interface Programming Some Power Supply Functions‘ --------------- Merge SETUP.BAS here 22 Remote Programming Programming Some Power Supply Functions continuedFOR I=1 TO Programming Some Power Supply Functions continuedSPOL%=O IF SPOL% AND 128 = 128 THEN POLL = 1 Set interrupt flag on OPER bit24 Remote Programming Programming Some Power Supply Functions continuedLanguage Dictionary Related CommandsCommon Commands Subsystem CommandsFigure 3-1. Common Commands Syntax Diagram Description Of Common Commands0 to Bit Configuration of Standard Event Status Enable RegisterMeaning and Type DescriptionQuery Syntax Related CommandsESR? IDN?PSC 0 *PSC Power-on Status Clear Device InitializationOPC? OPT?Description Meaning and TypeDescription Meaning and TypeDescription Meaning and TypeDescription Bit Configuration of Status Byte RegisterSTB? Meaning and TypeMeaning and Type TST?Meaning and Type DescriptionABOR Description of Subsystem CommandsCalibration Commands Figure 3-2. Subsystem Commands Tree DiagramCURRENTLEVEL 200 MA Current SubsystemCURR CURRTRIG CURRPROTSTATDisplay Subsystem Digital I/O Port Programming ChartPin Configuration1 ConfigurationDISPMODE NORM DISPTEXT DEFAULTMODEDISPMODE DISPTEXTMEASCURR? MEASVOLT? Initiate SubsystemMeasure Subsystem INIT INITCONTOUTP OUTPUTPROTECTIONDELAY 75E-1OUTPUTPROTDELAY MAX Output SubsystemOUTPRELPOL NORM OUTPRELOUTPRELPOL OUTPREL 1 OUTPREL OFFSTATPRES Bit Configuration of Operation RegistersBit Weight Status SubsystemSTATOPERENAB STATUSOPERATIONENABLE?STATOPER NTR STATOPER PTR STATQUESCOND? Bit Configuration of Questionable RegistersStatus Questionable Registers STATQUES?corresponding Questionable Event register System CommandsSTATQUES NTR STATQUES PTR SYSTERR?TRIG Trigger SubsystemSYSTLANG SYSTVERS?VOLTAGELEVEL 200 MV Voltage SubsystemTRIGSOUR VOLT VOLTTRIGVOLTPROT Command SummaryCommand Summary CommandSubsystem Commands Command ParametersCommand Summary CommandParameter Characteristics in the Operating GuideTable 3-1. Power Supply Programming Parameters see note Programming ParametersPage Status Reporting Power Supply Status StructureRegister Commands Table 4-1. Status Operation CommandsMeaning Table 4-2. Bit Configurations of Status RegistersSignal Figure 4-1. Power Supply Status ModelCLS *ESR? Table 4-3. Status Questionable CommandsQuestionable Status Group Standard Event Status GroupStatus Byte Register Service Request Enable RegisterInitial Conditions At Power On Determining the Cause of a Service InterruptTable 4-4. Default Power On Register States The PON Power-On BitServicing an Operation Status Mode Event information about encoding the commands as language stringsTable 4-5. Generating RQS from the CC Event Monitoring Both Phases of a Status TransitionAdding More Operation Events Servicing Questionable Status EventsTechniques in ANSI/IEEE Std SCPI Command CompletionDFI Discrete Fault Indicator RI Remote InhibitPage System Error Messages Error MessagesPower Supply Hardware Error Messages Calibration Error Messages60 Error Messages Table 6-1. Summary of System Error Messages continuedError Error String Description/Explanation/ExamplesSCPI Version SCPI Confirmed Commands1SCPI Approved Commands SCPI Conformance InformationNON-SCPI Commands1 Compatibility Language Command Table B-1. ARPS CommandsARPS Command1 Similar SCPIDescription Table B-1. ARPS Commands continuedARPS Command1 CommandDescription Table B-1. ARPS Commands continuedARPS Command1 CommandIndex 68 Index Page Canada Agilent Sales and Support OfficeUnited States Latin America