Manuals / Agilent Technologies / Power Tools / Work Light

Agilent Technologies 85036B, E manual Clean the Mating Plane Surfaces, Reinspect

Models: 85036B E

1 49

Download 49 pages 42.54 Kb

Page 21

Use, Maintenance, and Care of the Devices

Cleaning Connectors

Use a lint-free swab or cleaning cloth moistened with isopropyl alcohol to remove any dirt or stubborn contaminants on a connector that cannot be removed with compressed air or nitrogen. Refer to Table 6-3 on page 6-5for part numbers for isopropyl alcohol and cleaning swabs.

a.Apply a small amount of isopropyl alcohol to a lint-free cleaning swab.

b.Clean the connector threads.

c.Let the alcohol evaporate, then blow the threads dry with a gentle stream of clean, low-pressure compressed air or nitrogen. Always completely dry a connector before you reassemble or use it.

3.Clean the Mating Plane Surfaces

a.Apply a small amount of isopropyl alcohol to a lint-free cleaning swab.

b.Clean the center and outer conductor mating plane surfaces. When cleaning a female connector, avoid snagging the swab on the center conductor contact fingers by using short strokes.

c.Let the alcohol evaporate, then blow the connector dry with a gentle stream of clean, low-pressure compressed air or nitrogen. Always completely dry a connector before you reassemble or use it.

4.Reinspect

Inspect the connector again to make sure that no particles or residue are present.

85036B/E

3-5

Image 21

Agilent Technologies 85036B, E manual Clean the Mating Plane Surfaces, Reinspect

Contents

Manufacturing Part Number Print Date June User’s and Service GuideDocumentation Warranty Contents Standard Definitions Replaceable PartsGeneral Information Calibration Kit Overview Kit ContentsCalibration Definitions Installation of the Calibration DefinitionsEquipment Required but Not Supplied AdaptersIncoming Inspection Calibration Kit Contents Recording the Device Serial Numbers Serial Number Record for 85036BSerial Number Record for 85036E Calibration Kit History Calibration Kits Documented in this ManualAgilent 85036B kits with serial prefix 3102A and below Agilent 85036B kits with serial prefix 3103A and belowPreventive Maintenance Clarifying the Sex of a ConnectorSpecifications Temperature-What to Watch Out For Environmental RequirementsEnvironmental Requirements Supplemental Mechanical Characteristics Mechanical SpecificationsMechanical Specifications Mechanical CharacteristicsElectrical Specifications Electrical SpecificationsCertification Use, Maintenance, and Care of the Devices Electrostatic Discharge ESD Protection SetupVisual Inspection What Causes Connector Wear?Look for Obvious Defects and Damage First Inspect the Mating Plane SurfacesCleaning Connectors Inspect the Precision Slotless Connectors femaleUse Compressed Air or Nitrogen Reinspect Clean the Mating Plane SurfacesFinal Connection Using a Torque Wrench How to Make a ConnectionConnections Preliminary ConnectionWrench Positions Torque Wrench InformationUsing the Torque Wrench Connecting the Two-Piece Female Open How to Separate a ConnectionHandling and Storage Performance Verification How Agilent Verifies the Devices in This Kit IntroductionRecertification Where to Send a Kit for RecertificationLimited Recertification How Often to RecertifyRecertification 85036B/E Troubleshooting Troubleshooting Flowchart Troubleshooting ProcessContacting Agilent Returning a Kit or Device to AgilentReturning a Kit or Device to Agilent 85036B/E Replaceable Parts Adapters Replaceable Parts for the 85036B Calibration KitReplaceable Parts for the 85036B Calibration Kit Replaceable Parts for the 85036E Calibration Kit Miscellaneous Items Introduction 85036B/E Standard Definitions Table A-1 Standard Class Assignments Standard Class AssignmentsTable A-2 Standard Class Assignments Blank Form Blank FormNominal Standard Definitions Setting the System ImpedanceStandard b Offset Freq Table A-3 Standard DefinitionsTable A-4 Standard Definitions Blank Form Index Index-2 85036B/E Calibration