Table A-3 Standard Definitions | Agilent Technologies 85036B, E

Standard Definitions

Nominal Standard Definitions

Table A-3 Standard Definitions

System Z0a = 75 ΩCalibration Kit Label: N 75 Ω

Number	Type	10C0×	10C1×	10C2×	10C3×	SlidingorFixed	(ps)Delay	Z		/s)(LossΩ	Min		Max	WaveguideorCoax	LabelStandard
Standardb				2	3	c		Offset				Freq			d
				2	3	c					(GHz)				d
			F/Hz	F/Hz	F/Hz						(GHz)
		F
		F
		−15	−27	−36	−45
								Ω
								0

1	Short						0	75		1.13G	0		999	Coax	Short (m)d
2	Open	63.5	84	56	0		0	75		1.13G	0		999	Coax	Open (m)d
3	Load					Fixed	0	75		1.13G	0		999	Coax	Broad-
															band

4	Delay/						0	75		1.13G	0		999	Coax	Thru
	Thru

5

6

7	Short						17.544	75		1.13G	0		999	Coax	Short (f)d
8	Open	41e	40	5	0		17.544	75		1.13G	0		999	Coax	Open (f)d

a.Ensure system impedance (Z0) of network analyzer is set to this value.

b.Open, short, load, delay/thru, or arbitrary impedance.

c.Load or arbitrary impedance only.

d.Standard labels that specify sex, (m) or (f), refer to the sex of the analyzer’s test port connector.

e.If your instrument is an Agilent 8752B or 8711 Option 1EC, and you are calibrating at the test port, this number is 33. For all other instruments and applications, including calibrating at a point other than the test port (such as the end of a cable), 41 is the correct number. This is because the 8752B and 8711 Option 1EC have special female test ports with longer, more rugged fingers.

85036B/E

A-5

Image 45

Agilent Technologies 85036B, E manual Table A-3 Standard Definitions, Standard b Offset Freq

Contents

Manufacturing Part Number Print Date June User’s and Service Guide Documentation Warranty Contents Standard Definitions Replaceable Parts General Information Calibration Kit Overview Kit Contents Calibration Definitions Installation of the Calibration DefinitionsEquipment Required but Not Supplied Adapters Incoming Inspection Calibration Kit Contents Recording the Device Serial Numbers Serial Number Record for 85036BSerial Number Record for 85036E Calibration Kit History Calibration Kits Documented in this ManualAgilent 85036B kits with serial prefix 3102A and below Agilent 85036B kits with serial prefix 3103A and below Preventive Maintenance Clarifying the Sex of a Connector Specifications Temperature-What to Watch Out For Environmental RequirementsEnvironmental Requirements Supplemental Mechanical Characteristics Mechanical SpecificationsMechanical Specifications Mechanical Characteristics Electrical Specifications Electrical SpecificationsCertification Use, Maintenance, and Care of the Devices Electrostatic Discharge ESD Protection Setup Visual Inspection What Causes Connector Wear?Look for Obvious Defects and Damage First Inspect the Mating Plane Surfaces Cleaning Connectors Inspect the Precision Slotless Connectors femaleUse Compressed Air or Nitrogen Reinspect Clean the Mating Plane Surfaces Final Connection Using a Torque Wrench How to Make a ConnectionConnections Preliminary Connection Wrench Positions Torque Wrench Information Using the Torque Wrench Connecting the Two-Piece Female Open How to Separate a Connection Handling and Storage Performance Verification How Agilent Verifies the Devices in This Kit Introduction Recertification Where to Send a Kit for RecertificationLimited Recertification How Often to Recertify Recertification 85036B/E Troubleshooting Troubleshooting Flowchart Troubleshooting Process Contacting Agilent Returning a Kit or Device to Agilent Returning a Kit or Device to Agilent 85036B/E Replaceable Parts Adapters Replaceable Parts for the 85036B Calibration Kit Replaceable Parts for the 85036B Calibration Kit Replaceable Parts for the 85036E Calibration Kit Miscellaneous Items Introduction 85036B/E Standard Definitions Table A-1 Standard Class Assignments Standard Class Assignments Table A-2 Standard Class Assignments Blank Form Blank Form Nominal Standard Definitions Setting the System Impedance Standard b Offset Freq Table A-3 Standard Definitions Table A-4 Standard Definitions Blank Form Index Index-2 85036B/E Calibration