Calibration Kit History | Agilent Technologies 85036B, E instruction

General Information

Calibration Kits Documented in this Manual

Calibration Kits Documented in this Manual

This manual applies to any 85036B or 85036E calibration kit whose serial prefix is listed on the title page. If your calibration kit has a different serial number prefix than the one listed on the title page, refer to “Calibration Kit History” below for information on how this manual applies.

Calibration Kit History

This section describes calibration kits with serial number prefixes different than those listed on the title page.

Agilent 85036B kits with serial prefix 3102A and below

•75 ohm load specification: return loss ³ 45 db, dc to 2 GHz

•all other kit components unspecified

85036B calibration kits with serial number prefix 3102A and below should meet the specifications published in this manual. If you wish to have your kit recertified to current specifications, contact your nearest Agilent service center. For contact information, see Table 5-1 on page 5-3.

Agilent 85036B kits with serial prefix 3103A and below

These calibration kits had a center conductor extender with a smaller body. Therefore, a different procedure was used for connecting the female open. If you’re using one of the smaller extenders, replace steps 1 through 3 in “Connecting and Disconnecting the Two-Piece Female Open (85036B)” on page 3-9of this manual with the steps below.

1.Mate the center conductor extender to the male pin of the test port.

2.Connect the open body to the test port by carefully guiding it over the extender.

3.To disconnect the open, carefully remove the open body first.

The part numbers in this manual are the recommended replacement parts for these kits (including the center conductor extender).

85036B/E

1-7

Image 11

Agilent Technologies 85036B, E manual Calibration Kits Documented in this Manual, Calibration Kit History

Contents

Manufacturing Part Number Print Date June User’s and Service Guide Documentation Warranty Contents Standard Definitions Replaceable Parts General Information Calibration Kit Overview Kit Contents Adapters Installation of the Calibration DefinitionsCalibration Definitions Equipment Required but Not Supplied Incoming Inspection Calibration Kit Contents Serial Number Record for 85036E Recording the Device Serial NumbersSerial Number Record for 85036B Agilent 85036B kits with serial prefix 3103A and below Calibration Kits Documented in this ManualCalibration Kit History Agilent 85036B kits with serial prefix 3102A and below Preventive Maintenance Clarifying the Sex of a Connector Specifications Environmental Requirements Temperature-What to Watch Out ForEnvironmental Requirements Mechanical Characteristics Mechanical SpecificationsSupplemental Mechanical Characteristics Mechanical Specifications Certification Electrical SpecificationsElectrical Specifications Use, Maintenance, and Care of the Devices Electrostatic Discharge ESD Protection Setup Inspect the Mating Plane Surfaces What Causes Connector Wear?Visual Inspection Look for Obvious Defects and Damage First Use Compressed Air or Nitrogen Cleaning ConnectorsInspect the Precision Slotless Connectors female Reinspect Clean the Mating Plane Surfaces Preliminary Connection How to Make a ConnectionFinal Connection Using a Torque Wrench Connections Wrench Positions Torque Wrench Information Using the Torque Wrench Connecting the Two-Piece Female Open How to Separate a Connection Handling and Storage Performance Verification How Agilent Verifies the Devices in This Kit Introduction How Often to Recertify Where to Send a Kit for RecertificationRecertification Limited Recertification Recertification 85036B/E Troubleshooting Troubleshooting Flowchart Troubleshooting Process Contacting Agilent Returning a Kit or Device to Agilent Returning a Kit or Device to Agilent 85036B/E Replaceable Parts Adapters Replaceable Parts for the 85036B Calibration Kit Replaceable Parts for the 85036B Calibration Kit Replaceable Parts for the 85036E Calibration Kit Miscellaneous Items Introduction 85036B/E Standard Definitions Table A-1 Standard Class Assignments Standard Class Assignments Table A-2 Standard Class Assignments Blank Form Blank Form Nominal Standard Definitions Setting the System Impedance Standard b Offset Freq Table A-3 Standard Definitions Table A-4 Standard Definitions Blank Form Index Index-2 85036B/E Calibration