Manuals / Agilent Technologies / Kitchen Appliance / Water Dispenser

Agilent Technologies E4440A manual AC Power Cord, Power Requirements

Models: E4440A

1 84

Download 84 pages 39.65 Kb

Page 10

Table 1-1

Installation and Setup

Table 1-1

NOTE

WARNING

CAUTION

Installation and Setup

Power Requirements

Power Requirements

Description		Specification1
Voltage, Frequency	100 to 120 Vrms, 50/60/400 Hz
	220 to 240 Vrms, 50/60 Hz

Power Consumption, On	Base	Fully Loaded
	< 260 W	< 450 W

Power Consumption, Standby	< 20 W

1. For greater detail, refer to the Specifications Guide.

AC Power Cord

The analyzer is equipped with a three-wire power cord, in accordance with international safety standards. This cable grounds the analyzer cabinet when connected to an appropriate power line outlet. The cable appropriate to the original shipping location is included with the analyzer.

Various AC power cables are available that are unique to specific geographic areas. You can order additional AC power cables for use in different areas. AC Power Cords, on page 11 lists the available AC power cables, illustrates the plug configurations, and identifies the geographic area in which each cable is appropriate.

The front panel switch is a standby switch only; it is not a LINE switch (power disconnecting device).

Install the product so that the detachable power cord is readily identifiable and easily reached by the operator. The detachable power cord is the product disconnecting device. It disconnects the mains circuits from the mains supply before other parts of the product. The front panel switch is only a standby switch and is not a LINE switch. Alternatively, an externally installed switch or circuit breaker (which is readily identifiable and is easily reached by the operator) may be used as a disconnecting device.

Always use the three-prong AC power cord supplied with this product. Failure to ensure adequate earth grounding by not using this cord can cause product damage.

10

Chapter 1

Image 10

Agilent Technologies E4440A manual AC Power Cord, Power Requirements

Contents

E4440A 3 Hz - 26.5 GHz E4443A 3 Hz - 6.7 GHz Getting Started GuidePSA Series Spectrum Analyzers E4445A 3 Hz - 13.2 GHz E4446A 3 Hz - 44 GHzAdditional Information 2. Front and Rear Panel Features ContentsInstallation and Setup Options and AccessoriesContents Table of ContentsInstallation and Setup Installation and SetupAgilent Technologies Performance Spectrum Analyzer PSAAccessories Initial InspectionInstallation and Setup Power Cable See Table 1-2on pageIf There Is a Problem Power Requirements AC Power Cord Power RequirementsPower Requirements AC Power CordsInstallation and Setup Installation and SetupBattery Information Power RequirementsTurning on the Analyzer for the First Time Information ScreenIf Option 117 is Loaded in Memory Using an External Reference Firmware Revision Running Internal Alignments Manually Performing an AlignmentPrinter Setup and Operation EquipmentInstallation and Setup Installation and SetupPrinter Setup and Operation ChapterInterconnection and Setup Testing Printer OperationTest Equipment and ESD Protecting Against Electrostatic DischargeAdditional Information about ESD Safety Information Safety InformationFront and Rear Panel Features Front and Rear Panel FeaturesFront and Rear Panel Features Front-PanelConnectors and KeysFront Panel Overview and Rear Panel FeaturesChapter Front and Rear Panel FeaturesFront Panel Overview NamePanel Features Display AnnotationsFront and Rear Panel Features Front Panel OverviewFront Front and Rear Panel FeaturesFront Panel Overview ChapterFront Panel Overview Front and Rear Panel FeaturesFront and Rear Panel Features DescriptionRear-PanelFeatures Rear-PanelFeaturesFront and Rear Panel Features FrontFront and Rear Front and Rear Panel FeaturesRear-PanelFeatures DescriptionKey Overview Key OverviewChapter Key Overview Front and Rear Panel Symbols Do not dispose in domestic household wasteFront and Rear Panel Symbols more informationFront and Rear Panel Features Front and Rear Panel Features3 Making a Basic Measurement Making a Basic MeasurementBasic Assumption Using Menu Keys Using the Front PanelEntering Data Making a Basic Measurement Using the Front PanelMaking a Basic Measurement ChapterCreating a User Preset Presetting the Spectrum AnalyzerDisabling User Preset Viewing a Signal Setting Reference Level and Center FrequencyMaking a Basic Measurement Setting Frequency SpanViewing a Signal Making a Basic MeasurementReading Frequency & Amplitude Figure 3-2Span Changed to 50 MHzChanging Reference Level Making a Basic Measurement Figure 3-3A Marker on the 10 MHz PeakViewing a Signal Making a Basic MeasurementImproving Frequency Accuracy Valid Marker Count RangeMaking a Basic Measurement Figure 3-5Increasing Marker Frequency AccuracyViewing a Signal Making a Basic MeasurementMaking a Basic Measurement Figure 3-6Using Marker CounterViewing a Signal Making a Basic MeasurementFiles Viewing Catalogs and SavingViewing Catalogs and Saving Files This chapter tells you how to File Menu Functions Locating and viewing files in the catalogCatalog Menu Creating a directory File Menu Functions Step 1. Set up the analyzer trace Saving a FileFigure 4-3Viewing Traces 1 and Figure 4-2Viewing TraceSaving a File Step 2. Save the file Figure 4-4Viewing Traces 1, 2, andC \START\TEST1.TRC file saved Saving a FileLoading a file File LoadedVerifying Trace Saving a FileRenaming a File Figure 4-7Renaming a FileCopying a File Figure 4-8Copy MenuDeleting a File Using the Alpha Editor Options and Accessories Options and AccessoriesAccessories see page Ordering Options and AccessoriesOptions see page Options OptionsOptions and Accessories ChapterOption Options and AccessoriesOptions NameOptions Options and AccessoriesOptions ChapterOption Options and AccessoriesOptions NameChapter Options and AccessoriesOptions OptionOptions Options and AccessoriesOptions and Accessories Option50 Ohm/75 Ohm Minimum Loss Pad Accessories50 Ohm Load AC ProbeUSB/GPIB Interface Broadband Preamplifiers and Power AmplifiersGPIB Cable HP/Agilent 11970 Series Harmonic MixersPower Splitters RF and Transient Limiters50 Ohm Transmission/Reflection Test Kit Static Safe AccessoriesRF Bridges Noise Sources for use with PSA OptionIn Case of Difficulty In Case of DifficultyIf a problem persists, you may choose to Types of Spectrum Analyzer Messages Types of MessagesBefore Calling Agilent Technologies Check the Basicsanalyzer Calling Agilent Technologies Read the WarrantyService Options Contacting Agilent Technologies TableOriginal Packaging Returning an Analyzer for ServiceService Tag Other Packaging8.Retain copies of all shipping papers Numerics IndexIndex Index Index