Aiphone AXW-AVR Configuration Diagram, AX-DMor IE/IF-Series, Axw-Avt, Audio Door Station, Ax-Dv

CONFIGURATION DIAGRAM:

AXW-AVT / AXW-AVR with Infinova Fiber (N3732TA-M/-R, N3732RA-M/-R), 1 of 2

AX-DM or IE/IF-Series	AXW-AVT	PS-2420UL
Audio Door Station	24V
	+			+
	-		-

Configuration Notes (1 of 2, continued):

4.When the SENSOR input is used, the door station will be turned on whenever the sensor device is activated (Normally Closed contact from 3rd party supplied device).

RELAY	Normally Open contact for remote device activation
NO
NO	(i.e. video switcher, DVR, etc.)
SENSOR	Normally Closed input for remote activation
NC
NC	(i.e. motion sensor, loop detector, etc.)
CALL IN
+
-

5.The RELAY output provides an optional Normally Open dry contact output which is activated whenever the AX-series door station is in use. This can be used to

Infinova	activate any device local to the AXW-AVT
	(DVR trigger, video switcher activation,

CCTV Camera		CALL OUT
		+
75 Ohm, 1V Peak-to-peak		-
(Independently powered)		AUDIO IN
		+
		-
	*	AUDIO OUT
		+
		-
		DOOR
AX-DV		CAT-5e
		VIDEO IN
		Coax
		VIDEO OUT

Configuration Notes (1 of 2):

** **

Coaxial Video Cable

N3732TA-M		local call indication, etc.).
		6. Configure AXW-AVT internal jumpers as
	PWR	necessary (see Pg. 21).
	V

	Optic Fiber
OP	(to N3732TA-M, Pg. 9)
1
2	**The Infinova N3732TA provides only a
3
4

1.AX-series video door station connects to ‘DOOR’ input of AXW-AVT. Ensure that the “CCTV / DOOR’ switch on the AXW-AVT is in the ‘DOOR’ position.

*2. Alternatively, an IE/IF-series or AX-DM audio door may be used, along with 3rd party CCTV camera. Connect audio door station to ‘Door’ input (following the wiring method shown in the AX-series installation manual, pg. 12). Connect the camera to ‘Video In’ and put the ‘CCTV / DOOR’ switch in the ‘CCTV’ position.

3.Connect the Call In / Call Out and Audio In / Audio Out connections on the AXW-AVR to the terminal block of the Infinova N3732TA-M, as shown. For detailed terminal definitions, consult the Infinova installation document.

	single relay output, which may be used to
5
	control the door station’s standby mode
6
7	(when connected to the ‘Call Out’ terminals
8	on the AXW-AVT), or for door release. If
9
	utilized for door release, ensure that the
10
11	‘Call Out’ terminals on the AXW-AVT are
12	shorted together. Note: This will cause
13
14	the door station to be in a constant-on
15	state, which may reduce the lifespan of
16
	the AX-series door station.

Please Note:

Only information pertaining to the connection and operation of the AXW-AVT / AXW-AVR and listed 3rd party devices interfacing with it are included here. Aiphone is not responsible for attempts to connect the AXW-AVT / AXW-AVR to untested 3rd party transmission hardware. Consult the installation manual for the 3rd party device being utilized

	for further information regarding physical mounting, base functionality, power requirements,	etc. For the most up-to-date compatibility information, please consult http://
	www.aiphone.com or contact Aiphone Technical Support.
	For complete AX system installation, wiring, and programming information, please consult the AX Installation Manual (included on CD with AX Central Exchange Unit, or
Pg. 7	available at http://www.aiphone.com).	Pg. 8