Aiwa XR-MS3 manual Setting the Clock, Timer Recording

CLOCK AND TIMER

SETTING THE CLOCK

f,g CLOCK

a

If the clock display flashes

If the display flashes when the clock is displayed, it indicates that the clock has stopped due to a power failure or the removal of the power cord. The current time needs to be reset.

SETTING THE TIMER PLAYBACK

AND TIMER RECORDING

ENTER/

ILLUMINATION

	SHIFT	a
VOLUME/	ENTER/ILLUMINATION
MULTI JOG

1Press CLOCK while pressing SHIFT on the remote control. (You may press a on the main unit or

on the remote control while the power is off.)

The clock is displayed. (The ":" between the hours and minutes flashes.) When the power code is plugged into an AC outlet for the first time after purchase or when the clock setting is canceled due to a power failure, the entire clock display flashes.

POWER

FUNCTION

TUNER/BAND

JOG MODE

VOLUME/

MULTI JOG

ENTER/

ILLUMINATION

TUNER/BAND,

AUX,CD,TAPE

TIMER

SLEEP

POWER

SHIFT

ENTER/ILLUMINATION

2Within 4 seconds, turn VOLUME/MULTI JOG to

designate the hour and the minute.

Turn VOLUME/MULTI JOG to the right to advance the time and to the left to move the time back. The speed with which the time changes varies according to how fast you turn VOLUME/MULTI JOG. You can also press f or g. Holding these buttons down will vary the time in 10-minute units.

3Press ENTER/ILLUMINATION or a.

You may press ENTER/ILLUMINATION while pressing SHIFT on the remote control.

The clock starts form 00 seconds.

To view the clock when another display is in the display window

Press CLOCK while pressing SHIFT on the remote control. The time is displayed for 4 seconds and then the original display reappears.

However, the clock cannot be displayed during recording.

To switch to the 24-hour standard

Press CLOCK while pressing SHIFT on the remote control, and then press swithin 4 seconds.

Repeat the same procedure to restore the 12-hour standard. In the 12-hour standard, "AM 12:00" indicates midnight and "PM 12:00" indicates noon.

When the clock is set for the first time after purchase

All the display lights turn off when the power is off. (Only the red indicator lights up.)

This is because the power economizing mode of the unit is activated, and is not a malfunction. To view the clock in this case, press CLOCK while pressing SHIFT on the remote control so that the time is displayed for 4 seconds. (Alternatively, press ENTER/ILLUMINATION or a on the main unit.) Besides, the time will be displayed if you deactivate the power economizing mode. (See page 7 for details.)

The unit can be turned on at a specified time every day with the built-in timer.

First, make sure the clock is set correctly.

1Select the source.

Use FUNCTION on the main unit or one of the function buttons (TUNER/BAND, AUX, CD or TAPE) on the remote control to select the source for timer playback or timer recording.

2Select timer playback or timer recording.

Press JOG MODE repeatedly until "TIMER" appears on the display, and within 6 seconds, turn VOLUME/MULTI JOG to select timer playback or timer recording.

When using the remote control, press TIMER repeatedly while pressing SHIFT.

"TIMER5PLAY" for timer playback "TIMER5REC" for timer recording

3Within 6 seconds, press ENTER/ILLUMINATION.

When using the remote control, press ENTER/ILLUMINATION while pressing SHIFT.

Time and source display flash alternately.

4Set the timer-on time.

Turn VOLUME/MULTI JOG to the right to advance the time and to the left to move the time back. The speed with which the time changes varies according to how fast you turn VOLUME/MULTI JOG. You can also use for g. Holding these buttons down will vary the time in 10-minute units.

18 ENGLISH