AKG Acoustics CS 5 9.2 CS 5 DU/VU

Section 9: Specifications

9.2 CS 5 DU/VU

9.2.1 General

9.2.2 Connector Pinouts

CS 5 User Manual - 46 -

Minimum Nominal Maximum Unit

Power Supply

Supply voltage 46 48 50 V

Power consumption -1.5 3 W

Headphone Output

Power -30 60 mW

Load impedance 832 -ohms

Frequency range (-3 dB) 45 -22k Hz

Physical Dimensions

Signal/noise ratio 70 - - dB

Width 10.1/257 in./mm

Depth 5.8/147 in./mm

Height 1.9/73 in./mm

HEADPHONE

1/4" TRS jack*

Pin no. Function

Tip Right

Ring Left

Sleeve Ground

SYSTEM

8-pin RJ45

Pin no. Function

1Data send +

2Data send -

3Data receive +

448 VDC

548 VDC

6Data receive -

7Ground

8Ground

*Use stereo headphones with TRS plugs only. Connecting a TS plug would short the ring contact to ground

and damage the device.

Contents

Main Page Table of Contents Symbols Used Safety and Environment Safety Instructions Environment FCC Statement Section 1: General 2.1 Notes on Wiring and System Configuration Page 2.2.2 Computer-controlled Discussion System Page Page Page 3.1 General 3.2 Front Panel 3.3 Rear Panel Page 3.4.2 Configuring the Dip Switches 3.4.3 Selecting NOM Limitation/Interpretation Channels 3.4.4 Powering Up 3.4.5 Setting Levels 3.4.6 Selecting NOM Limitation/Interpretation Channels Section 4: CS 5 DU Delegate Station 4.1 Introduction 4.2 Controls, Inputs, and Outputs Section 4: CS 5 DU Delegate Station 4.3 Setting Up 4.3.1 Making Connections 4.3.2 Selecting Operating Modes Page 5.1 Introduction 5.2 Control Panel, Inputs, and Outputs Page 5.3 Setting Up 5.3.1 Making Connections 5.3.2 Selecting Operating Modes 5.3.3 DELEGATE Mode 5.3.4 PRESIDENT Mode 5.4 Voting/Polling 5.4.1 Controlling a Ballot or Opinion Poll (PRESIDENT Mode) 5.4.2 Voting in DELEGATE Mode 5.5 Chip Card Identification 6.1 Introduction 6.2 Control Panel, Inputs, and Outputs 6.3 Setting Up 6.3.1 Making Connections 6.3.2 Selecting Station Addresses 6.3.3 Selecting Target Language Channels 6.3.4 List of Available Language Names 6.3.5 Selecting the Microphone Type 6.4 Using the Interpreter Station Page 7.1 CS 5 IRT 1 and CS 5 IRT 2 Infrared Radiators 7.1.1 General 7.1.2 Placement 7.1.3 Mounting 7.1.4 Connections 7.2 CS 5 IRR 7 Infrared Receiver 7.2.1 General 7.2.2 Using the Infrared Receiver 7.2.3 Replacing Batteries 7.3 CS 5 CU 50 Charger/Storage Case 7.3.1 General 7.3.2 Charging Batteries 7.3.3 Battery Care Section 8: System Components 9.1 CS 5 BU 9.1.1 General 9.1.2 Connector Pinouts Page 9.2 CS 5 DU/VU 9.2.1 General 9.2.2 Connector Pinouts CS 5 IU 9.3.1 General 9.3.2 Connector Pinouts 9.4 CS 5 PS 12 9.5 CS 5 IRT 1 and CS 5 IRT 2 9.6 CS 5 IRR 7 9.7 CS 5 CU 50 9.8 Conformity