Section 3: CS 5 BU Base Unit
3.4.2Configuring the Dip Switches
1.Before powering up, set all front panel level controls to minimum (smallest dot) and set the rear panel dip switches as required. Refer to fig. 3 on page 15 and Table 1 below.
Dip switch | Function | Switch position | ||
|
| |||
0 | 1 | |||
|
| |||
|
|
|
| |
S1 | routes LINE IN to | NORMAL bus | EFFECTS bus | |
|
|
|
| |
S2 | routes EXT. MIC. IN to | NORMAL bus | EFFECTS bus | |
|
|
|
| |
S3 | routes TAPE IN to | NORMAL bus | EFFECTS bus | |
|
|
|
| |
S4 | routes SYSTEM BUS IN to | NORMAL bus | EFFECTS bus | |
|
|
|
| |
S5 | switches NOM attenuation on SYSTEM BUS OUT | OFF | ON | |
|
|
|
| |
S6 | switches NOM attenuation on LINE OUT | OFF | ON | |
|
|
|
| |
S7 | EXT. LANG. signal | muted | routed to Channel 1 | |
|
|
|
| |
S8 | Microphone activation mode | Floor request opens available mic channel | FIFO: Floor request opens available mic | |
|
| or puts microphone on waiting list. | channel or cancels earliest floor request. | |
|
|
|
| |
Table 1: Base Unit dip switches.
•Dip switches S1 to S4 route the LINE, EXT. MIC., TAPE, and SYSTEM inputs to either the NORMAL or EFFECTS bus. The NORMAL bus feeds the mixed input signals to the TAPE, LINE, SYSTEM, 
, and INFRA outputs.
The EFFECTS bus signal is available at the EFFECT output where you can connect a feedback eliminator or other effects device. Connect the output of your effects device to the EFFECT IN jack on the rear panel. The processed signal is fed to the NORMAL bus. As long as no effects device is connected, the signal is routed to the NORMAL bus.
•Dip switches S5 and S6 let you activate and deactivate NOM attenuation. NOM (Number of Open Microphones) at- tenuation reduces the volume of the loudspeakers in a sound system depending on the number of microphones that are active at any time. The more microphones are open, the more the loudspeaker volume is reduced. S5 al- lows you to activate NOM attenuation for the loudspeakers on the microphone stations connected to SYSTEM out- puts. S6 lets you activate NOM attenuation on the LINE OUT signal that feed the room sound system.
•Dip switch S7 allows you to select the input signal for system channel 1. To route the assigned Interpreter Station output to channel 1, set S7 to "0". To route the EXT. LANG. input to channel 1, set S7 to "1". You can use the lat- ter configuration for a consecutive interpreter with a hardwire or wireless microphone.
•Dip switch S8 selects one of two microphone activation modes.
-With S8 in position "0", a microphone will be switched on immediately on pressing the talk button ("requesting the floor") if a microphone channel is available. If no microphone channel is available, the microphone requesting the floor will be put on the waiting list.
-With S8 in position "1", a microphone will be switched on immediately on pressing the talk button if a microphone channel is available. If no microphone channel is available, the floor request on top of the waiting list will be deleted and the last microphone requesting the floor will be added to the waiting list.
3.4.3Selecting NOM Limitation/Interpretation Channels
•Set NOM LIMIT (7) to the desired ratio between the maximum number of microphones that may be open at any time and the number of channels available for interpretation.
If no interpretation is needed, you may set NOM LIMIT to "64/0", allowing 64 microphones to be open simultane- ously. To reduce the number of open microphones, set NOM LIMIT to a lower position.
If interpretation will be provided, set NOM LIMIT for the number of interpretation channels required (e.g., "48/16" for any number of interpretation channels up to 16 and 48 open microphones).
CS 5 User Manual | - 16 - |
