Swivel Assembly, CENTER 4-WAY GEAR BOX, Maintenance | Alamo TX235

SWIVEL ASSEMBLY

MAINTENANCE

MAINTENANCE

SWIVEL ASSEMBLY

The Swivel Assembly should be lubricated every 8 hours. Mnt-R-0278.

CENTER 4-WAY GEAR BOX

Gearbox is filled from factory with proper lube level. To check oil level remote test plug on front side gear. It is recommended that oil level plug be removed every 100 hours of operation and oil added until it runs out test plug hole. The test plug is located in front cap of gearbox. Fill plug is on top of gearbox.

Recommended lubricant is NGLI 000 (P/N 00765444). Gearbox capacity is 1-1/8 Quarts.

TX235 02/07

Maintenance Section 5-4

© 2007 Alamo Group Inc.

Image 140

Alamo TX235 manual Swivel Assembly, CENTER 4-WAY GEAR BOX, Maintenance

Contents

RHINO TURF FLEXTX235 OPERATOR’S MANUAL To the Owner/Operator/Dealer Page one 1 AEM Mower Safety Practices Video Alamo Group Ag. Division is willing to provide TABLE OF CONTENTS SAFETY SECTIONASSEMBLY SECTION INTRODUCTION SECTION MAINTENANCE SECTION SAFETY SECTION Safety Section General Safety Instructions and Practices SAFETYSAFETY Operator Safety Instructions and Practices “Wait a minute...Save a life!” SG-36 Equipment Operation Safety Instructions and Practices SAFETY SAFETY SAFETY SGM-06 SGM-08 STOP MOWING IF PASSERSBY ARE WITHIN 100 YARDS UNLESS S3PT-14 Transporting Safety Instructions and Practices S3PT-02 SAFETY Maintenance and Service Safety Instructions and Practices SAFETY SEE YOUR RHINO DEALER Storage and Parking Safety Instructions and PracticesConcluding Safety Instructions and Practices Decal Location LEVEL DESCRIPTION Decal Description SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY Federal Laws and Regulations Employer-Employee Operator RegulationsEmployer Responsibilities Child Labor Under 16 Years of AgePage Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page INTRODUCTION SECTION Introduction Section INTRODUCTION INTRODUCTION INTRODUCTION Attention Owner/Operator ASSEMBLY SECTION Assembly Section ASSEMBLY ASSEMBLYDEALER SET-UP INSTRUCTIONS TONGUE JACK AND WHEEL ATTACHMENT SWIVEL AND LIFT ARM ATTACHMENT Asm-R-0325 HYDRAULIC CYLINDER ATTACHMENTWING MOWER ATTACHMENT CASTER WHEEL ATTACHMENTS - REAR MOWER CASTER WHEEL ATTACHMENTS - WING MOWER REAR MOWER ATTACHMENT DRIVELINE ATTACHMENT JACKSTAND AND HOSE ATTACHMENT HYDRAULIC HOSE ATTACHMENT 3-SPOOL VALVELOCK-UP ARMS ATTACHMENT SMV ATTACHMENT ASSEMBLY Standard Driveline FIELD ASSEMBLYWING DRIVELINE ATTACHMENT OPERATION SECTION Operation Section RHINO TX235 TURF FLEX FINISHING MOWER OPERATION INSTRUCTIONS OPERATIONOPERATION 1. Standard Equipment and Specifications 2. OPERATOR REQUIREMENTS PERSONAL PROTECTIVE EQUIPMENT PPE 3.2 Tractor Safety Devices 3. TRACTOR REQUIREMENTSTractor Requirements and Capabilities 3.1 ROPS and Seat Belt 3.3 Drawbar 3.4 Front End Weight3.5 Power Take Off PTO 4.2 Dismounting the Tractor 4. GETTING ON AND OFF THE TRACTOR4.1 Boarding the Tractor 5. STARTING THE TRACTOR 6.2 Safety Tow Chains 6. CONNECTING THE MOWER TO THE TRACTOR6.1 Connecting the Mower Tongue to the Tractor Hydraulic Cylinder Priming 7. SETTING THE MOWER6.3 Connecting Mower Hydraulics 8. DRIVELINE ATTACHMENT Cutting Height AdjustmentROLLER ADJUSTMENT 8.1 Driveline Length Check “Bottoming Out” Check Procedure Engagement Check Procedure Shorten the driveline profiles as follows 8.2 Constant Velocity CV Driveline CV Driveline Maximum Angle Check Procedure 9. PRE-OPERATION INSPECTION AND SERVICE 9.1 Tractor Pre-Operation Inspection/Service 9.2 Mower Pre-Operation Inspection/Service OPERATION OPERATION OPERATION OPERATION OPERATION Finish Mower PRE-OPERATION Inspection DO NOT OPERATE an UNSAFE TRACTOR or MOWERMower ID#Make DateShift Condition at Tractor PRE-OPERATION Inspection 10. DRIVING THE TRACTOR AND IMPLEMENT 10.2 Brake and Differential Lock Setting 10.1 Starting the Tractor 10.3 Transporting the Cutter Transport Position 10.4 Operating the Tractor and Mower Operating Position 10.5 Crossing Ditches and Steep Inclines 11. OPERATING THE TRACTOR AND IMPLEMENT 11.2 Bystander/Passerby Precautions 11.1 Foreign Debris Hazards 11.3 Engaging the Power Take Off PTO 11.4 PTO RPM and Ground Speed 11.5 Operating the Mower OPERATION 11.6 Shutting Down the Implement 12. DISCONNECTING THE MOWER FROM THE TRACTOR 13. MOWER STORAGE 14. TRANSPORTING THE TRACTOR AND IMPLEMENT OPERATION 14.1 Transporting on Public Roadways OPERATION 14.2 Hauling the Tractor and Implement 15. TROUBLESHOOTING GUIDE PROBLEMPOSSIBLE CAUSE POSSIBLE REMEDY PROBLEM OPERATIONOPERATION POSSIBLE CAUSE PROBLEM OPERATIONOPERATION POSSIBLE CAUSEPage MAINTENANCE SECTION Maintenance Section LUBRICATION INFORMATION MAINTENANCEMAINTENANCE GEARBOX SWIVEL ASSEMBLY CENTER 4-WAY GEAR BOX NOTE Do not overlube as excess grease may get on belt drive GAUGE WHEEL ASSEMBLIESBLADE SPINDLE LUBRICATION DRIVELINE LUBRICATION CV DRIVELINE PROFILE LUBRICATION WING DRIVELINE PROFILE LUBRICATION BLADE SERVICING BLADE INSTALLATION BLADE SHARPENING BELT ADJUSTMENT PROCEDURE BELT REMOVAL / INSTALLATION BLADE SPINDLE SERVICE INSTRUCTIONS DISASSEMBLYASSEMBLY NOTE Direction of seal lip on top side STORAGE PROPER TORQUE FOR FASTENERS LIMITED WARRANTY RHINORHINO WARRANTY LIMITATIONS - GEARBOX TO THE OWNER/OPERATOR/DEALERD Maintaining proper bearing preload on all gearbox shaft REQUIRED OF THE OWNER TX235 TURF FLEX Rotary Mower TX235-SOM-02/07P/N 00767122C Printed U.S.A