Hydraulic Cylinder Attachment, Wing Mower Attachment | Alamo TX235

HYDRAULIC CYLINDER ATTACHMENT

ASSEMBLY

ASSEMBLY

HYDRAULIC CYLINDER ATTACHMENT

Attach the Rear Hydraulic Cylinder to the Main Frame with Fittings pointing up. Retain with Pin and Cotter Pin. Asm-R- 0324. Attach the Wing Hydraulic Cylinders to the Main Frame and toggle links with pins provided.

Asm-R-0325.

WING MOWER ATTACHMENT

NOTE: The Wing Mowers are right and left mowers. The offset rear caster wheel is to the inside when the mower is installed.

Position the Wing Mowers under the Wing Lift Arms and remove the Attachment Pin (1) from the Swivel. Attach the Wing Mower to the Lift Arm and secure with 1/2" x 1-1/2" Bolt (2), flatwasher (3), and locknut (4).

TX235 02/07

Assembly Section 3-4

© 2007 Alamo Group Inc.

Image 88

Alamo TX235 manual Hydraulic Cylinder Attachment, Wing Mower Attachment, Assembly, Asm-R-0325

Contents

RHINO TURF FLEXTX235 OPERATOR’S MANUAL To the Owner/Operator/Dealer Page one 1 AEM Mower Safety Practices Video Alamo Group Ag. Division is willing to provide TABLE OF CONTENTS SAFETY SECTIONASSEMBLY SECTION INTRODUCTION SECTION MAINTENANCE SECTION SAFETY SECTION Safety Section SAFETY SAFETYGeneral Safety Instructions and Practices Operator Safety Instructions and Practices “Wait a minute...Save a life!” SG-36 Equipment Operation Safety Instructions and Practices SAFETY SAFETY SAFETY SGM-06 SGM-08 STOP MOWING IF PASSERSBY ARE WITHIN 100 YARDS UNLESS S3PT-14 Transporting Safety Instructions and Practices S3PT-02 SAFETY Maintenance and Service Safety Instructions and Practices SAFETY Concluding Safety Instructions and Practices Storage and Parking Safety Instructions and PracticesSEE YOUR RHINO DEALER Decal Location LEVEL DESCRIPTION Decal Description SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY Federal Laws and Regulations Employer-Employee Operator RegulationsEmployer Responsibilities Child Labor Under 16 Years of AgePage Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page INTRODUCTION SECTION Introduction Section INTRODUCTION INTRODUCTION INTRODUCTION Attention Owner/Operator ASSEMBLY SECTION Assembly Section ASSEMBLY ASSEMBLYDEALER SET-UP INSTRUCTIONS TONGUE JACK AND WHEEL ATTACHMENT SWIVEL AND LIFT ARM ATTACHMENT WING MOWER ATTACHMENT HYDRAULIC CYLINDER ATTACHMENTAsm-R-0325 CASTER WHEEL ATTACHMENTS - REAR MOWER CASTER WHEEL ATTACHMENTS - WING MOWER REAR MOWER ATTACHMENT DRIVELINE ATTACHMENT JACKSTAND AND HOSE ATTACHMENT HYDRAULIC HOSE ATTACHMENT 3-SPOOL VALVELOCK-UP ARMS ATTACHMENT SMV ATTACHMENT ASSEMBLY WING DRIVELINE ATTACHMENT FIELD ASSEMBLYStandard Driveline OPERATION SECTION Operation Section OPERATION OPERATIONRHINO TX235 TURF FLEX FINISHING MOWER OPERATION INSTRUCTIONS 1. Standard Equipment and Specifications 2. OPERATOR REQUIREMENTS PERSONAL PROTECTIVE EQUIPMENT PPE 3.2 Tractor Safety Devices 3. TRACTOR REQUIREMENTSTractor Requirements and Capabilities 3.1 ROPS and Seat Belt 3.5 Power Take Off PTO 3.4 Front End Weight3.3 Drawbar 4.1 Boarding the Tractor 4. GETTING ON AND OFF THE TRACTOR4.2 Dismounting the Tractor 5. STARTING THE TRACTOR 6.1 Connecting the Mower Tongue to the Tractor 6. CONNECTING THE MOWER TO THE TRACTOR6.2 Safety Tow Chains 6.3 Connecting Mower Hydraulics 7. SETTING THE MOWERHydraulic Cylinder Priming ROLLER ADJUSTMENT Cutting Height Adjustment8. DRIVELINE ATTACHMENT 8.1 Driveline Length Check “Bottoming Out” Check Procedure Engagement Check Procedure Shorten the driveline profiles as follows 8.2 Constant Velocity CV Driveline CV Driveline Maximum Angle Check Procedure 9. PRE-OPERATION INSPECTION AND SERVICE 9.1 Tractor Pre-Operation Inspection/Service 9.2 Mower Pre-Operation Inspection/Service OPERATION OPERATION OPERATION OPERATION OPERATION Finish Mower PRE-OPERATION Inspection DO NOT OPERATE an UNSAFE TRACTOR or MOWERMower ID#Make DateShift Condition at Tractor PRE-OPERATION Inspection 10. DRIVING THE TRACTOR AND IMPLEMENT 10.2 Brake and Differential Lock Setting 10.1 Starting the Tractor 10.3 Transporting the Cutter Transport Position 10.4 Operating the Tractor and Mower Operating Position 10.5 Crossing Ditches and Steep Inclines 11. OPERATING THE TRACTOR AND IMPLEMENT 11.2 Bystander/Passerby Precautions 11.1 Foreign Debris Hazards 11.3 Engaging the Power Take Off PTO 11.4 PTO RPM and Ground Speed 11.5 Operating the Mower OPERATION 11.6 Shutting Down the Implement 12. DISCONNECTING THE MOWER FROM THE TRACTOR 13. MOWER STORAGE 14. TRANSPORTING THE TRACTOR AND IMPLEMENT OPERATION 14.1 Transporting on Public Roadways OPERATION 14.2 Hauling the Tractor and Implement 15. TROUBLESHOOTING GUIDE PROBLEMPOSSIBLE CAUSE POSSIBLE REMEDY PROBLEM OPERATIONOPERATION POSSIBLE CAUSE PROBLEM OPERATIONOPERATION POSSIBLE CAUSEPage MAINTENANCE SECTION Maintenance Section MAINTENANCE MAINTENANCELUBRICATION INFORMATION GEARBOX SWIVEL ASSEMBLY CENTER 4-WAY GEAR BOX BLADE SPINDLE LUBRICATION GAUGE WHEEL ASSEMBLIESNOTE Do not overlube as excess grease may get on belt drive DRIVELINE LUBRICATION CV DRIVELINE PROFILE LUBRICATION WING DRIVELINE PROFILE LUBRICATION BLADE SERVICING BLADE INSTALLATION BLADE SHARPENING BELT ADJUSTMENT PROCEDURE BELT REMOVAL / INSTALLATION BLADE SPINDLE SERVICE INSTRUCTIONS DISASSEMBLYASSEMBLY NOTE Direction of seal lip on top side STORAGE PROPER TORQUE FOR FASTENERS RHINO RHINOLIMITED WARRANTY WARRANTY LIMITATIONS - GEARBOX TO THE OWNER/OPERATOR/DEALERD Maintaining proper bearing preload on all gearbox shaft REQUIRED OF THE OWNER TX235 TURF FLEX Rotary Mower TX235-SOM-02/07P/N 00767122C Printed U.S.A