Field Assembly, Wing Driveline Attachment | Alamo TX235 guide

FIELD ASSEMBLY

ASSEMBLY

ASSEMBLY

FIELD ASSEMBLY

1.Loop ends back through welded link on lock bar and then inside of braid by forming a hole 16” from end.

2.Adjust lengths as shown to give 8” overlap and 4” loop.

3.Adjust to give dimensions shown.

4.Secure loops by running a plastic tie through rope braids (2) to prevent slipping.

WING DRIVELINE ATTACHMENT

Standard Driveline

Attach the wing driveline to the center power divider gearbox as shown so that both sides of the gearbox are oriented the same.

NOTE: The driveline end with the extended shield cone attaches to the mower deck gearbox. Asm-R-0333.

TX235 02/07

Assembly Section 3-10

© 2007 Alamo Group Inc.

Image 94

Alamo TX235 manual Field Assembly, Wing Driveline Attachment, Standard Driveline

Contents

TX235 RHINOTURF FLEX OPERATOR’S MANUAL To the Owner/Operator/Dealer Page one 1 AEM Mower Safety Practices Video Alamo Group Ag. Division is willing to provide ASSEMBLY SECTION TABLE OF CONTENTSSAFETY SECTION INTRODUCTION SECTION MAINTENANCE SECTION SAFETY SECTION Safety Section SAFETY SAFETYGeneral Safety Instructions and Practices Operator Safety Instructions and Practices “Wait a minute...Save a life!” SG-36 Equipment Operation Safety Instructions and Practices SAFETY SAFETY SAFETY SGM-06 SGM-08 STOP MOWING IF PASSERSBY ARE WITHIN 100 YARDS UNLESS S3PT-14 Transporting Safety Instructions and Practices S3PT-02 SAFETY Maintenance and Service Safety Instructions and Practices SAFETY Concluding Safety Instructions and Practices Storage and Parking Safety Instructions and PracticesSEE YOUR RHINO DEALER Decal Location LEVEL DESCRIPTION Decal Description SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY SAFETY Employer Responsibilities Federal Laws and RegulationsEmployer-Employee Operator Regulations Child Labor Under 16 Years of AgePage Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page INTRODUCTION SECTION Introduction Section INTRODUCTION INTRODUCTION INTRODUCTION Attention Owner/Operator ASSEMBLY SECTION Assembly Section DEALER SET-UP INSTRUCTIONS ASSEMBLYASSEMBLY TONGUE JACK AND WHEEL ATTACHMENT SWIVEL AND LIFT ARM ATTACHMENT WING MOWER ATTACHMENT HYDRAULIC CYLINDER ATTACHMENTAsm-R-0325 CASTER WHEEL ATTACHMENTS - REAR MOWER CASTER WHEEL ATTACHMENTS - WING MOWER REAR MOWER ATTACHMENT DRIVELINE ATTACHMENT JACKSTAND AND HOSE ATTACHMENT LOCK-UP ARMS ATTACHMENT HYDRAULIC HOSE ATTACHMENT3-SPOOL VALVE SMV ATTACHMENT ASSEMBLY WING DRIVELINE ATTACHMENT FIELD ASSEMBLYStandard Driveline OPERATION SECTION Operation Section OPERATION OPERATIONRHINO TX235 TURF FLEX FINISHING MOWER OPERATION INSTRUCTIONS 1. Standard Equipment and Specifications 2. OPERATOR REQUIREMENTS PERSONAL PROTECTIVE EQUIPMENT PPE Tractor Requirements and Capabilities 3.2 Tractor Safety Devices3. TRACTOR REQUIREMENTS 3.1 ROPS and Seat Belt 3.5 Power Take Off PTO 3.4 Front End Weight3.3 Drawbar 4.1 Boarding the Tractor 4. GETTING ON AND OFF THE TRACTOR4.2 Dismounting the Tractor 5. STARTING THE TRACTOR 6.1 Connecting the Mower Tongue to the Tractor 6. CONNECTING THE MOWER TO THE TRACTOR6.2 Safety Tow Chains 6.3 Connecting Mower Hydraulics 7. SETTING THE MOWERHydraulic Cylinder Priming ROLLER ADJUSTMENT Cutting Height Adjustment8. DRIVELINE ATTACHMENT 8.1 Driveline Length Check “Bottoming Out” Check Procedure Engagement Check Procedure Shorten the driveline profiles as follows 8.2 Constant Velocity CV Driveline CV Driveline Maximum Angle Check Procedure 9. PRE-OPERATION INSPECTION AND SERVICE 9.1 Tractor Pre-Operation Inspection/Service 9.2 Mower Pre-Operation Inspection/Service OPERATION OPERATION OPERATION OPERATION OPERATION Mower ID#Make DateShift Finish Mower PRE-OPERATION InspectionDO NOT OPERATE an UNSAFE TRACTOR or MOWER Condition at Tractor PRE-OPERATION Inspection 10. DRIVING THE TRACTOR AND IMPLEMENT 10.2 Brake and Differential Lock Setting 10.1 Starting the Tractor 10.3 Transporting the Cutter Transport Position 10.4 Operating the Tractor and Mower Operating Position 10.5 Crossing Ditches and Steep Inclines 11. OPERATING THE TRACTOR AND IMPLEMENT 11.2 Bystander/Passerby Precautions 11.1 Foreign Debris Hazards 11.3 Engaging the Power Take Off PTO 11.4 PTO RPM and Ground Speed 11.5 Operating the Mower OPERATION 11.6 Shutting Down the Implement 12. DISCONNECTING THE MOWER FROM THE TRACTOR 13. MOWER STORAGE 14. TRANSPORTING THE TRACTOR AND IMPLEMENT OPERATION 14.1 Transporting on Public Roadways OPERATION 14.2 Hauling the Tractor and Implement POSSIBLE CAUSE 15. TROUBLESHOOTING GUIDEPROBLEM POSSIBLE REMEDY OPERATION PROBLEMOPERATION POSSIBLE CAUSE OPERATION PROBLEMOPERATION POSSIBLE CAUSEPage MAINTENANCE SECTION Maintenance Section MAINTENANCE MAINTENANCELUBRICATION INFORMATION GEARBOX SWIVEL ASSEMBLY CENTER 4-WAY GEAR BOX BLADE SPINDLE LUBRICATION GAUGE WHEEL ASSEMBLIESNOTE Do not overlube as excess grease may get on belt drive DRIVELINE LUBRICATION CV DRIVELINE PROFILE LUBRICATION WING DRIVELINE PROFILE LUBRICATION BLADE SERVICING BLADE INSTALLATION BLADE SHARPENING BELT ADJUSTMENT PROCEDURE BELT REMOVAL / INSTALLATION ASSEMBLY BLADE SPINDLE SERVICE INSTRUCTIONSDISASSEMBLY NOTE Direction of seal lip on top side STORAGE PROPER TORQUE FOR FASTENERS RHINO RHINOLIMITED WARRANTY D Maintaining proper bearing preload on all gearbox shaft WARRANTY LIMITATIONS - GEARBOXTO THE OWNER/OPERATOR/DEALER REQUIRED OF THE OWNER P/N 00767122C TX235 TURF FLEX Rotary MowerTX235-SOM-02/07 Printed U.S.A