Alcatel Carrier Internetworking Solutions 8008 3-30, VLAN Port Configuration

Web Interface

3-30VLAN Port Configuration

Use this screen to configure port-specific settings for IEEE 802.1Q VLAN features.

Parameter Description

PVID The VLAN ID assigned to untagged frames received on this port. Use t he

PVID to assign ports to the same untagged VLAN.

Acceptable Frame

Type1

This switch accepts “All” frame types, including VLAN tagged or VLAN

untagged frames. Note that all VLAN untagged frames received on this po rt

are assigned to the PVID for this port.

Ingress Filtering1If set to “True,” incoming frames for VLANs which do not inclu de this port in

their member set will be discarded at the inbound port.

GVRP Status2Enables or disables GVRP for this port. When disabled, any GVRP packets

received on this port will be discarded and no GVRP registrations will be

propagated from other ports.

Note that, before this port setting takes effect, GVRP must be enabled for the

switch (see Configuring Bridge MIB Extensions on page 3-21).

GVRP Failed

Registrations2

The total number of failed GVRP registrations, for any reason, on this port.

GVRP PDU Origin2The Source MAC Address of the last GVRP message received on this port.

1. This control does not affect VLAN independent BPDU frames, such as GVRP or STP. However, it does

affect VLAN dependent BPDU frames, such as GMRP.

2. GVRP is not available for the current firmware release.

Contents

Main Page Page Page Contents Page Page Page 1-1 Chapter 1: Switch Management Configuration Options Required Connections Console Port (Out-of-Band) Connections Page 2-1 Chapter 2: Console Interface Log-in Screen 2-2 Main Menu The Main Menu is the first screen seen after successfully logging into the system. Main Menu 2-3 Page System and Switch Information 2-6 Displaying System Information System and Switch Information 2-7 Displaying Switch Version 2-8 Management Setup Menu 2-9 Changing the Network Configuration 2-10 IP Configuration 2-11 IP Connectivity Test (Ping) Page 2-13 Configuring the Serial Port 2-14 Assigning SNMP Parameters 2-15 2-16 2-17 Console Login Configuration 2-18 Downloading System Software 2-19 Saving the System Configuration Page 2-21 Configuring the Banner Message 2-22 Configuring the Switch 2-23 2-24 Configuring Port Parameters 2-25 Viewing the Current Port Configuration Page 2-27 The following figure and table describe Bridge STA configuration. 2-28 The following figure and table describe STA configuration for ports. 2-29 Page 2-31 2-32 The parameters shown in the following figure and table are for port STA Information. 2-33 Using a Mirror Port for Analysis 2-34 Configuring Port Trunks 2-35 Page 2-37 2-38 Configuring Broadcast Storm Control 2-39 Port Security Configuration 2-40 Configuring Bridge MIB Extensions 2-41 Configuring Traffic Classes 2-42 2-43 2-44 Configuring Virtual LANs 2-45 2-46 2-47 2-48 Use this screen to configure port-specific settings for IEEE 802.1Q VLAN features. 2-49 Monitoring the Switch 2-50 Displaying Port Statistics 2-51 Displaying RMON Statistics 2-52 2-53 Displaying the Unicast Address Table 2-54 Displaying the IP Multicast Registration Table 2-55 Configuring Static Unicast Addresses 2-56 Resetting the System Logging Off the System 3-1 Chapter 3: Web Interface Web-Based Configuration and Monitoring 3-2 Navigating the Web Browser Interface Home Page Page 3-4 Panel Display Port State Display Panel Display 3-5 Configuring the Serial Port 3-6 Main Menu System Information 3-7 System Information Switch Information IP Configuration 3-9 IP Configuration 3-10 SNMP Configuration SNMP Community Security Configuration 3-11 Trap Managers Security Configuration Change Password 3-12 Firmware Upgrade Options Web Upload Management Page 3-14 Configuration Save and Restore Configuration Upload Management Configuration Download Management Address Table Configuration 3-15 Address Table Configuration 3-16 STA (Spanning Tree Algorithm) Spanning Tree Information STA (Spanning Tree Algorithm) 3-17 The parameters shown in the following figure and table are for port STA Information (Port 1~8). Page STA (Spanning Tree Algorithm) 3-19 3-20 STA Port Configuration The following figure and table describe STA configuration for ports. Configuring Bridge MIB Extensions 3-21 Configuring Bridge MIB Extensions Bridge Capability Page Priority 3-23 Priority Port Priority Configuration Page 3-25 Configuring Virtual LANs VLAN Basic Information 3-26 VLAN Current Table 3-27 VLAN Static List VLAN Static Table Page Page 3-30 VLAN Port Configuration Use this screen to configure port-specific settings for IEEE 802.1Q VLAN features. IGMP Multicast Filtering 3-31 IGMP Multicast Filtering Configuring IGMP Page Port Menus 3-34 Port Configuration Use the Port Configuration menus to configure any port on the switch. Port Menus 3-35 Port Broadcast Storm Protect Configuration Page Using a Port Mirror for Analysis 3-37 Using a Port Mirror for Analysis Port Trunk Configuration Page Port Statistics 3-39 Port Statistics Etherlike Statistics 3-40 RMON Statistics Port Statistics 3-41 Page 4-1 Chapter 4: Advanced Topics Layer 2 Switching Spanning Tree Algorithm Advanced Topics 4-2 Virtual LANs Virtual LANs 4-3 Assigning Ports to VLANs Automatic VLAN Registration (GVRP) Page Multicast Filtering 4-5 Multicast Filtering IGMP Snooping IGMP Protocol Advanced Topics 4-6 Class-of-Service (CoS) Support Port Trunks SNMP Management Software Remote Monitoring 4-7 Remote Monitoring Page A-1 Appendix A: Troubleshooting Troubleshooting Chart Troubleshooting A-2 Upgrading Firmware via the Serial Port Page Page B-1 Appendix B: Pin Assignments Console Port to 9-Pin COM Port on PC Console Port Pin Assignments DB-9 Port Pin Assignments Pin Assignments B-2 Console Port to 25-Pin DTE Port on PC Glossary Page Page Page Index Index-1 Numerics A B Index Index-2 O P Q Page www.alcatel.co www.alcatel.com/enterprise