Manuals / Alliance Laundry Systems / Home Audio / Speaker

Alliance Laundry Systems 9001889R7 manual Calibration of the Machine

Models: 9001889R7

1 62

Download 62 pages 8.61 Kb

Page 30

Calibration of the Machine

Programming

Program Cycle 00

Total working hours : 0

level : 0.0 “ Enter to zero

Spin

XXX rpm

Reference x.xx

Calibration of the Machine

The _x__PV should reflect the size selected in earlier steps.

Turn key to Program Mode.

Press “Auxiliary”, “3”, “1”.

The total hours the machine was running will be displayed.

Press “Advance” and screen will show total cycles. Press “Advance” to calibrate the water level sensor.

If the value is not zero, press “Enter” and the value will change to zero.

Press “Advance” to calibrate the motor.

The board will lock the door and let the motor spin at approximately 500 rpm (Firmware version 1.12 or higher). The rpm will increase on the display. If the machine reached approximately 500 rpm, the display will show a reference value.

After the reference value is shown, the machine will coast down to stop. When the machine stands still, the board will unlock the door.

28

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

9001889

Image 30

Alliance Laundry Systems 9001889R7 manual Calibration of the Machine

Contents

Cabinet Freestanding Washer-ExtractorsProgramming WE-8ComputerPage W030 Table of Contents Introduction Model IdentificationSetup of the Machine ProgrammingPress the “Enter” button to select options Select between 1 to 9 cm or inches Version of Control Program Storing ModeLanguage on Display Version 1.15 and later ONLY Explanation of the Step Functions NOTE If a fill error occurs, then machine hasFill Example Fill to low level and 95F step time limit Wash SupplyChemical Hold Feature Wash 5 Thermal Cool-DownSoak Spin DrainExample Making a New Program Warm ProgrammingStep 01 Cycle SupplyStep 03 Cycle Programming9001889 HeatStep 06 Cycle 51 Spin Step 06 Cycle 51 0 min ProgrammingStep 06 Cycle Step 06 Cycle 51 Spin Step 06 Cycle 51 8 min 30 secEdit a Cycle Change a Complete StepPress “Enter” to confirm Changing the Time of a Step Step 02 Cycle 51 6 min 20 sec ProgrammingStep 02 Cycle 51 6 min 00 sec Step 03 CycleDelete a Step Insert a Step Press “Enter” to confirm Program Cycle Delete a CycleProgramming Erase CycleProgram Cycle Enter to reload earlier settings Reloading Previous SettingsPress “Enter” to confirm the settings Press “Auxiliary”, “3”, “0”Cycle Count Reading Cycle CountCalibration of the Machine Speed Calibration Pre-ProgrammedCycles Hot Fill to Low Level Hot Fill to Low Level Warm Fill to High Level Description Pre-ProgrammedCycles Cycle Towels Heavy SoilStep Min secWarm Fill to High Level 32F Fill to High Level 110F Fill to High Level Step Pre-ProgrammedCycles CycleHealth Care Personal Bleach Description110F Fill to Low Level Description Pre-ProgrammedCycles Cycle Table Linen No IronStep Min secDescription Cycle Table Color No IronStep Min secDescription Pre-ProgrammedCycles Cycle Visa No IronStep Min secDescription Cycle Visa Color No IronStep Min secDescription Pre-ProgrammedCycles Cycle Shirt Bleach StarchStep Min secDescription Cycle Shirt DelicateStep Min secDescription Pre-ProgrammedCycles Cycle Uniforms BleachStep Min secDescription Cycle Rags Heavy SoilStep Min secStep Cycle Supply SetupPre-ProgrammedCycles Cycle Rewash/Reclaim DescriptionCold Fill to High Level Description Pre-ProgrammedCycles Cycle Energy HotStep Min secCold Fill to Low Level Warm Fill to Low Level Description Cycle Gentle ColdStep Min secDescription Pre-ProgrammedCycles Cycle Perm Press 60CStep Min secCold Fill to High Level Name Inverter Drive Error CodesOperation Description and NOTESOperation Inverter Drive Error CodesNote Resetting the inverter initializes NameName Inverter Drive Error CodesOperation Description and NOTESName Inverter Drive Error CodesOperation Description and NOTES