Alto-Shaam ar-7evh manual Elec T RIC a L Connection

ELEC T RIC A L CONNECTION

The appliance must be installed by a qualified service technician. The oven must be properly grounded in accordance with the National Electrical Code and applicable local codes.

d a n G E r

To avoid electrical shock, this appliance MUST be adequately grounded in accordance with local electrical codes or, in the absence of local codes, with the current edition of the National Electrical Code ANSI/ NFPA No. 70. In Canada, all electrical connections are to be made in accordance with CSA C22.1, Canadian Electrical Code Part 1 or local codes.

Plug the unit into a properly grounded receptacle ONLY, positioning the unit so that the plug is easily accessible in case of an emergency. Arcing will occur when connecting or disconnecting the unit unless all controls are in the “off” position.

Proper receptacle or outlet configuration or permanent wiring for this unit must be installed by a licensed electrician in accordance with applicable local electrical codes.

After wiring and power connection has been completed, turn the main power switch to the “on” position. The main power switch can be left “on” for daily use, but should be turned “off” when cleaning or performing maintenance or repairs to the rotisserie.

“WarnIng” rISk OF FIre!

use a ul listed grounding type plug rated 250 Volts, 50 amperes, 1 phase, 3 wire for single phase units and 250 V, 50 a, 3 phase, 4 wire for three phase units. plug to be selected and installed only by qualified service personnel. Individual conductors are marked l1, l2, l3 when applicable, n when applicable, and g.

danGEr

APPLIANCES WITH NO CORD

PROVIDED BY FACTORY MUST

BE EQUIPPED WITH A CORD OF

SUFFICIENT LENGTH TO PERMIT

THE APPLIANCE TO BE MOVED

FOR CLEANING.

ELECTRICAL CONNECTIONS MUST

BE MADE BY A QUALIFIED SERVICE

TECHNICIAN IN ACCORDANCE WITH

APPLICABLE ELECTRICAL CODES.

I n s t a l l a tio n

ElEctrIcal

VOLTAGE	PHASE CYCLE/HZ		AMPS	KW
208 (AGCY)	1	60	40.0	8.4	BARE END NO PLUG
240 (AGCY)	1	60	38.0	8.9
208 (AGCY)	3	60	33.0/ph 8.4		BARE END NO PLUG
240 (AGCY)	3	60	32.0/ph 8.9
380-415 (AGCY)	3	50	24.0/ph 8.9
380	3	50	22.0/ph 7.5 NO CORD NO PLUG
415	3	50	24.0/ph 8.9

Wire diagrams are located in the inside access panel of the unit.

REGARDING INTERNATIONAL STANDARD UNITS:

If the unit is not equipped with flexible cord with plug, an all-pole country approved disconnection device which has a contact separation of at least 3mm in all poles must be incorporated in the fixed wiring for disconnection. When using a cord without a plug, the green/yellow conductor shall be connected to the terminal which is marked with the ground symbol.

If a plug is used, the socket outlet must be easily accessible. If the power cord needs replacement, use a similar one obtained from the distributor.

For CE approved units: To prevent an electrical

shock hazard between the appliance and other appliances or metal parts in close vicinity, an equalization-bonding stud is provided. An equalization bonding lead must be connected to this stud and the other appliances / metal parts to provide sufficient protection against potential difference. The terminal is marked

with the following symbol.

power cord connection: The side connection is recommended for all applications. If a bottom connection is necessary for counter top units, user will need to provide a cutout in the countertop to allow the cord to hang freely without crimping.

hard wired models:

Hard wired models must be equipped with a country certified external allpole disconnection switch with sufficient contact separation.

If a power cord is used for the connection of the product an oil resistant cord like H05RN or H07RN or equivalent must be used.

notE: CE approved appliances must be connected to an electrical circuit that is protected by an external GFCI outlet.

danGEr

ENSURE POWER SOURCE

MATCHES VOLTAGE STAMPED

ON APPLIANCE NAMEPLATE.

AR-7EVH Electric Rotisserie with Ventless Hood Operation & Care Manual • 5