Manuals / AMX / Computer Equipment / Network Card

AMX NXC-ME260 instruction manual Verifying the current version of NetLinx Master firmware

Models: NXC-ME260

1 106

Download 106 pages 58.54 Kb

Page 26

Verifying the current version of NetLinx Master firmware

Communication and Firmware Update

FIG. 16 Assigning Communication Settings and Baud Rates

7.Set the COM port parameters for the selected COM port being used for communication to the NetLinx Master. Default parameters are: COM1, 38400, 8 Data Bits, No Parity, 1 Stop Bit, and No Flow Control.

8.Click OK three times to close the open dialogs and save your settings.

If the connection fails to establish:

Select a different COM port, press the Retry button to reconnect using the same communication parameters, or press the Change button to alter your communication parameters and repeat steps 2 thru 8.

Verifying the current version of NetLinx Master firmware

1.Click on the OnLine Tree tab in the Workspace window to view the devices on the System. The default System value is one (1).

2.Right-click on the Empty Device Tree entry and select Refresh System to establish a new connection to the System’s Master and refresh the list with online system devices. The communication method is highlighted in green on the bottom of the NetLinx Studio window.

The current firmware version of the Master is displayed to the right of the device.

3.After the Communication Verification dialog window verifies active communication between the PC and the Master, verify the NetLinx Master appears in the OnLine Tree tab of the Workspace window (FIG. 17).

4.If the firmware version is not build 139 (v2_XX_139) for the NXC-ME260, follow the procedures outlined in the following sections to assign System/Device values, setup an IP Address, and then transfer the new firmware KIT file to the Master.

	20	NXC-ME260 NetLinx Master-Ethernet Card/Module

Image 26

AMX NXC-ME260 instruction manual Verifying the current version of NetLinx Master firmware

Contents

NetLinx Master-Ethernet Card/Module NXC-ME260instruction manual NetLinx Central Controllers and CardsAMX Limited Warranty and Disclaimer Product Information Table of ContentsInstallation and Wiring Communication and Firmware Update NetLinx Security and Web ServerNetLinx Security with a Terminal Connection Programming Product Information Front and rear panel componentsProduct Information SpecificationsNXC-ME260 Specifications Rear panel LEDs Ethernet NXC-ME260 Specifications ContRear panel LEDs ICSNet/ICSHub Product InformationProduct Information NXC-ME260 NetLinx Master-Ethernet Card/ModuleBaud rate settings Installation and WiringSetting the Program Port DIP Switch Baud Rate SettingsSetting the Program Port DIP switch Preparing captive wires Wiring GuidelinesModes and Front Panel LED Blink Patterns Modes and LED Blink PatternsWiring a 2-pin power connection Wiring length guidelinesWiring Length Guidelines @ 750 mA Using the 4-pin mini-Phoenix connector for data and powerProgram Port Connections and Wiring Using the 4-pin mini-Phoenix connector for data with external power5-Pin Program Port Pinouts and Signals ICSNet RJ-45 Connections/WiringRS232 Program Port, Pinouts, and Signals ICSNet RJ-45 SignalsRJ-45 Pinout Information EIA/TIA 568 B ICSHub RJ-45 Connections/WiringICSHub IN Pinouts and Signals ICSHub IN portEthernet RJ-45 Pinouts and Signals Ethernet 10/100 Base-T RJ-45 Connections/WiringICSHub OUT Pinouts and Signals ICSHub OUT portEthernet Ports Used by the ME260 SPE Port Connection/WiringEthernet ports used by the ME260 SPE cable pinout information SPE Connector Pinouts and SignalsInstallation and Wiring Mounting the NXS-NMS Into an Equipment Rack NXC-ME260 Installation and Mounting ProceduresMounting the ME260 into an NXS-NMS Mounting the NXC-ME260 in an NXF CardFrame or NXI FIG. 15 Lithium battery and socket Replacing the Lithium BatteriesBattery CR2032 type - 20mm coin cell socket Installation and Wiring NXC-ME260 NetLinx Master-Ethernet Card/ModuleBefore beginning Communication and Firmware UpdateCommunicating with the Master via the Program Port Verifying the current version of NetLinx Master firmware Setting the System Value Select Diagnostics Device Addressing from the Main menu4. Press the System Connection button Working with multiple NetLinx MastersChanging the system value on the Modero panel Device Address original device value Check-Off to verify change Changing the Device Address on a Netlinx DeviceSelect Diagnostics Device Addressing from the Main menu FIG. 19 Device Addressing dialog changing the device valueRecommended NetLinx Device numbers there is a problem, use a system value of zero 0 on the MasterChanging the device address on the Modero panel Select Diagnostics Device Addressing from the Main menu Resetting the Factory Default System and Device ValuesObtaining the Master’s IP Address using DHCP 8. Click OK to accept the new changes Assigning a Static IP to the NetLinx Master 1. Select Diagnostics Network Addresses from the Main menuCommunicating with the NetLinx Master via an IP FIG. 22 Assigning Communication Settings and TCP/IP SettingsNXC-ME260 NetLinx Master-Ethernet Card/Module Installing New NetLinx Master Firmware via an IPCommunication and Firmware Update 7. Select the Master’s KIT file from the Files section FIG 13. Click Close once the download process is complete Communication and Firmware Update NXC-ME260 NetLinx Master-Ethernet Card/ModuleSupported Browser and Feature Compatibility NetLinx Security and Web ServerNetLinx Security web browser and feature support Master Security Telnet Security Terminal RS232 Program port security New Master Firmware Security FeaturesNetLinx Security Terms HTTP Web Server Security FTP SecurityNetLinx Security Terms Cont Accessing the NetLinx Master via an IP AddressWebControl Tab greater than 139. The ME260 cannot use firmware greater thenDefault Security Configuration Default Security ConfigurationWebControl Tab Features Security Options FTP Security - EnabledSecurity link is selected Security TabSecurity Tab Features Security System Features Security Tab Features ContSecurity tab - Enable Security page This field will not be enabled until after the initialAdd Group Entries Security System Features ContSecurity tab - Add Group page Modify Group Entries Add Group Entries ContSecurity tab - Modify Group page Modify Group Entries Cont Security tab - Group Directory Associations pageDirectory Association has been assigned to the account Here are some examples of valid entriesValid Directory Association Entries Group Directory Association EntriesNetLinx Security and Web Server Security tab - Add User pageAdd User Entries NetLinx Integrated ControllersSecurity tab - Modify User page Modify User EntriesModify User Entries Cont Security tab - User Directory Associations pageValid Directory Association Entries User Directory Association EntriesSecurity tab - SSL Server Certificate page Server Certificate EntriesServer Certificate Entries Cont certificate because the Master Key has been changedFIG. 34 Security Tab - Export Certificate Request field Security tab - Export Certificate Request pageSecurity tab - Import Certificate page FIG. 35 Security Tab - Import Certificate fieldNetwork Tab System TabShow Devices Tab Master Security Setup Procedures FIG. 38 Security tab - showing NetLinx Master security optionsAdding a Group and assigning their access rights The administrator group account cannot be deleted or modifiedModifying an existing Group’s access rights FIG. 40 Security tab - showing the Modify Group access rights fieldsShowing a list of authorized Groups Deleting an existing GroupAdding a Group directory association Valid Directory Association Entries2. Click the Directory Associations link The administrator user account cannot be deleted or modifiedConfirming the new directory association Deleting a directory associationAdding a User and configuring their access rights NetLinx cannot be used since they already existModifying an existing User’s access rights Showing a list of authorized Users Deleting a UserAdding a User directory association 2. Click the Directory Associations link SSL Certificate ProceduresConfirming the new directory association Deleting a directory associationself-generating a certificate Self-Generating a SSL Server Certificate RequestThis domain name does not need to be resolvable URL Address when The city/province name must be fully spelled outCreating a Request for a SSL Server Certificate The state/province name must be fully spelled outImporting a CA certificate to the Master over a secure SSL connection Before importing a CA server certificate, you mustDisplay SSL Server Certificate Information Regenerating an SSL Server Certificate RequestCommon Steps for Requesting a Certificate from a CA 7. Before exiting the Master and beginning another session4. Enter the name of the server being used this is the Master Accessing an SSL-Enabled Master via an IP Address 7. Click Next to proceed with the certificate store process Using your NetLinx Master to control the G4 panel Using your NetLinx Master to control the G3 panel The ME260 cannot use firmware greater thenWhat to do when a Certificate Expires a new certificate from your current CANetLinx Security with a Terminal Connection NetLinx Security FeaturesInitial Setup via a Terminal Connection NetLinx Security FeaturesAccessing the Security configuration options Stop bits1, and Flow control None default is HardwareIf NetLinx Master security is not enabled, you will see the following Option 3 - Add user Security Options MenuOption 2 - Display system security options for NetLinx Master Option 4 - Edit User Edit User MenuNetLinx Security with a Terminal Connection Access Rights MenuEdit User Menu Option 6 - Show the list of authorized users Access Rights MenuOption 5 - Delete user Option 7 - Add GroupEdit Group Menu Edit Group Menu Add directory associationEdit Group menu List directory associations Edit Group menu Change Access RightsEdit Group menu Delete directory association Option 9 - Delete Group Edit Group menu Display Access RightsOption 8 - Edit Group Option 10 - Show List of Authorized Groups Option 11 - Set Telnet Timeout in secondsOption 12 - Display Telnet Timeout in seconds Option 13 - Make changes permanent by saving to flashNetLinx Security with a Terminal Connection Main Security MenuMain Security Menu were added. This is a permanent change and you will be Default Security ConfigurationMain Security Menu Cont NetLinx Security with a Terminal Connection Help menuHelp Menu Options Logging Into a Session Help Menu Options ContHelp Security LogoutSetup Security PC COM Port Communication Settings Program Port CommandsProgramming Program Port CommandsTIME Program Port Commands ContSET DATE SET TIMEGET IP DPS Program Port Commands ContDISK FREE MSG ON or MSG OFFPASS DPS Program Port Commands ContREBOOT DPS PING IP ADDRESSSENDCOMMAND DPS Program Port Commands ContROUTE MODE DIRECTNORMALSHOW COMBINE Program Port Commands ContSET URL DPS SHOW DEVICE DPSSHOW NOTIFY Program Port Commands ContSHOW LOG ProgrammingSHOW ROUTE Program Port Commands ContSHOW REMOTE SHOW SYSTEMESC Pass Codes ESC Pass CodesProgram Port Commands Cont TCP LISTLinux Telnet client Notes on Specific Telnet/Terminal ClientsWindows client programs Programming NXC-ME260 NetLinx Master-Ethernet Card/ModuleRevisionLast04/05/04