Antunes, AJ SE-4200/4400 WATER FILTRATION SYSTEM, OPERATION continued, Reset Defaults Mode

SE-4200/4400 WATER FILTRATION SYSTEM

OPERATION (continued)

7.	The system displays the FLUSH BY PRESS DIFF		RESET DEFAULTS MODE
	display. If the filtration system came with pressure	1.		From the FILTER MODE display, press the Stop
	transducers installed, this feature is available.
				button. The system displays the STOP MODE dis-
	If no transducers are installed, this feature is
				play.
	ignored. The default value is on. This should be
			2. Press the Menu button.
	appropriate for most locations. Use the Left and
	Right Arrow Buttons to make the desired change		3. Using the Up and Down arrow buttons, scroll from
	and then press the Enter button.			SET PASSWORD to RESET DEFAULTS and press
NOTE: If the FLUSH BY PRESS DIFF option is set				the Enter button.
to “off,” the system will then display the DEMAND		4.		The system displays the ENTER PASSWORD dis-
SENSOR display which is protected by a special				play. The default password is AAAA. Use the Up
password. Leave the DEMAND SENSOR option				and Down arrow buttons to enter the password.
OFF and press the Enter button to go to the				After each entry, press the Enter button.
PREFLUSH display. For more information on the				If you enter the wrong password, the system will
DEMAND SENSOR option, contact the manufac-
				display the ACCESS DENIED. PRESS ‘ENTER’ TO
turer.
				CONTINUE message. Press Enter or wait and the
8.	If the FLUSH BY PRESS DIFF setting is set to
				system will prompt you for the password again.
	on, the system will then prompt for a pressure
	differential value. The default value is 21 psi,			IMPORTANT
	which should be fine for most locations. To		If you cannot remember your password, call
	change this value, use the Up and Down arrow		Technical Service immediately for assistance.
	buttons to make a change. Then, press the Enter	5.		The system displays the TURN OFF POWER,
	button.			WAIT 10 SEC, RESTORE POWER message.
9.	The system displays the PREFLUSH display. The			Unplug the power cord and wait for ten (10) sec-
	default value is on. This should suit most loca-			onds or more, and then plug the cord in again.
	tions. To change this value, use the Left and		6. The system then cycles through initialization
	Right arrow buttons to select on or off. Press			displays and prompts you to set the Date and
	the Enter button to accept the change (or to			Time. Follow the instructions in the Set Date/Time
	accept the default value if a change is not made).			Modes section of this manual. The system can
10.	Regardless of the setting of the PREFLUSH			then be re-programmed as desired.
	option, the system then displays the BACKWASH		REVIEW OF CYCLES MODE
	LENGTH prompt. The default for this option is	1.		From the FILTER MODE display, press the Stop
	00:20 seconds which should be fine for most
				button. The system displays the STOP MODE dis-
	locations. Enter the desired length of time for the
				play.
	backwash operation in mm:ss format. Press the
	Enter button to accept the change (or to accept		2. Press the Menu button.
	the default value if a change is not made).		3. Using the Up and Down arrow buttons, scroll to
11.	Next, the system displays the FORWARD FLUSH
				REVIEW OF CYCLES. Press the Enter button.
	LENGTH prompt. Enter the desired length of time	4.		The system displays the REVIEW HISTORY dis-
	for the forward flush operation in mm:ss format.
				play. The default value is off. Use the Left
	The default value is 00:10 seconds, which should
				and Right arrow buttons to toggle between off
	be fine for most locations. Press the Enter but-
				and on. With the setting set to on, use the Up
	ton to accept the change (or to accept the default
				and Down arrow buttons to view a history of
	value if a change is not made).
				keystrokes with date and time information. This
12.	The system displays the SET FLUSH CYCLE dis-
				information can be used to determine causes of
	play. If you need to correct any settings, press			problems or assist in servicing the system.
	enter and make the desired changes. If changes
	are not necessary, press the Menu button to
	return to the STOP MODE display.
13.	Press the Run button to return to FILTER MODE.
P/N 1010852 Rev. C 04/06		13