Manuals / Brands / Computer Equipment / Computer Hardware / Asus / Computer Equipment / Computer Hardware

Asus TX97-XE VOLCTL, Volume Up, (momentary), Volume Down, (momentary), Audio Control, 16.Wake on LAN (3-pinWOL), ASUS TX97-XEUser’s Manual

1 72

Download 72 pages, 1.35 Mb

III.INSTALLATION

15.Onboard Digital Audio Control (VOLCTL) (with optional onboard Audio) This jumper allows you to adjust the audio volume digitally using case mounted momentary buttons.

Audio Control	VOLCTL
Volume Up	[1-2]	(momentary)
Volume Down	[4-5]	(momentary)
		VOLCTL
		1	Ground
		2	Volume Up
		3	Ground
		4	Volume Down
		5	Ground

Onboard Digital Audio Control

16.Wake on LAN (3-pin WOL)

This connector connects to LAN cards with a Wake On LAN output. When the system is in soft-off mode, LAN activity will power on the system.

Wake On LAN Connector

INSTALLATION	Connectors
III.

ASUS TX97-XE User’s Manual

Contents

Page USER'S NOTICE Product Name: ASUS TX97-XE Manual Revision: Release Date: ASUSTeK COMPUTER INC Marketing Technical Support ASUS COMPUTER INTERNATIONAL ASUS COMPUTER GmbH CONTENTS CONTENTS FCC & DOC COMPLIANCE Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver How this Manual is Organized Item Checklist Features of the ASUS TX97-XEMotherboard ASUS TX97 Smart Series Motherboards Series TX97 II.FEATURES Voltage Monitoring and Alert: CPU Slow Down Auto Fan Off even in sleep mode Parts of the ASUS TX97-XEMotherboard ASUS TX97-XEMotherboard Layout Jumpers Expansion Slots Connectors INSTALLATION Map of Board Installation Steps 1. Jumpers Jumper Settings III.INSTALLATION 3.Onboard Multi-I/OSelection (M/IO) Chipset Features Setup Multi-I/OM/IO Enable Page Compatible Cyrix CPU Identification 2.System Memory (SIMM & DIMM) SIMM Memory Installation DIMM Memory Installation Procedures 3.Central Processing Unit (CPU) 4.Expansion Cards Expansion Card Installation Procedure: Assigning IRQs for Expansion Cards Assigning DMA Channels for ISA Cards ISA Cards and Hardware Monitor 5.External Connectors 3.Parallel Printer Connector (25-pinFemale) NOTE 4.Serial Port COM1 and COM2 Connectors (Two 9-pinMale) 5.Floppy Disk Drive Connector (34-1pinFLOPPY) Line In Line Out Mic Joystick/Midi Connector 9.Primary / Secondary IDE connectors (Two 40-1pinIDE) 10.IDE activity LED (2-pinIDE_LED) 11.Chassis , CPU , & Power Supply Fan Connectors (3-pinFANPWR) do not place jumper caps over these pins 12.Chassis Open Alarm Lead (4-1pinCHASSIS) comes from the power supply, when the A/C is connected 13.IrDA / Fast IR-Compliantinfrared module connector (5-pinIR) 14.ATX Power Supply Connector (20-pinATXPWR) Onboard Digital Audio Control (VOLCTL) (with optional onboard Audio) Audio Control VOLCTL Volume Up (momentary) 17.Message LED Lead (MSG LED) 18.System Management Interrupt Lead (SMI) 19.ATX Power Switch / Soft Power Switch (PWR SW) 20.Reset Switch Lead (RESET) 21.System Power LED (PWR LED) Power Connection Procedures Support Software Flash Memory Writer Utility Main Menu 2. Update BIOS Including Boot Block and ESCD Flash Memory Writer IV. BIOS Managing and Updating Your Motherboard’s BIOS 6. BIOS Setup Load Defaults Standard CMOS Setup Details of Standard CMOS Setup: Time Hard Disk Drives For IDE hard disk drive setup, you can: •Use theAuto setting for detection during bootup •Enter the specifications yourself manually by using the “User” option Auto detection of hard disks on bootup Auto Drive A / Drive B (None) Floppy 3 Mode Support (Disabled) Drive A BIOS Features Setup Details of BIOS Features Setup BIOS BIOS HDD Sequence SCSI/IDE First (IDE) IDE SCSI Boot Sequence (C,A) Video ROM BIOS Shadow (Enabled) C8000 - CBFFF Shadow to DC000 - DFFFF Shadow (Disabled) Boot Up NumLock Status (On) This field enables users to activate the Number Lock function upon system boot Typematic Rate Setting (Disabled) Chipset Features Setup Details of Chipset Features Setup 8-bitI/O Recovery Time (1 BUSCLK) Timing for 8-bitISA cards Video BIOS Cacheable (Enabled) Memory Hole At Address (None) 14MB-16MB UART2 Use Infrared (Disabled) Onboard PCI IDE Enable (Both) Primary Secondary Both Power Management Setup Details of Power Management Setup Video Off Method (DPMS OFF) PM Timers HDD Power Down Doze Standby PWR Up On Modem Act (Enabled) AC PWR Loss Restart (Disabled) Automatic Power Up (Disabled) Everyday By Date PNP and PCI Setup Details of PNP and PCI Setup DMA x Used By ISA (No/ICU) ISA MEM Block BASE (No/ICU) SYMBIOS SCSI BIOS (Auto) Auto PnP / PCI Load BIOS Defaults Load Setup Defaults Supervisor Password and User Password IDE HDD Auto Detection Save & Exit Setup Exit Without Saving Desktop Management Interface (DMI) Introducing the ASUS DMI Configuration Utility System Requirements Using the ASUS DMI Configuration Utility Notes Save MIFD Load MIFD Load BIOS Defaults Page User’s Notice ASUS 16-bitAudio Manual Revision: March ASUS Audio User’s Manual ASUS Audio CD ASUS Audio Driver CD Contents Drivers Audio Win95 Installation Drivers Win95 Audio Drivers Audio Drivers Installation Procedures: Configuration Manager Creative PnP Configuration Manager (CTCM) Drivers Audio x.Win3 Manager .Config You will get the following message after you press <ENTER>: Press <ENTER> to continue, <F1> for help, <F2> for README, or <F3> to exit The following lines will be added to your system files: Audio Software Installation Audio C:\AUTOEXEC.BAT SET BLASTER=A220 I5 D1 H5 P330 T6 SET SOUND=C:\VIBRA16 SET MIDI=SYNTH:1 MAP:E C:\WINDOWS\WIN.INI C:\WINDOWS\SYSTEM.INI C:\WINDOWS\CONTROL.INI Page Environment Variables SOUND Environment variable BLASTER Environment Variable MIDI Environment Variable Maximum Recording Rates for the Audio Hardware