Atlas Sound XLTE owner manual Phillips pan-head screws, Footnotes for Physical Features

OTHER MOUNTING POINTS

	GRILLE MOUNTING POINTS	The grille is fastened to the enclosure with 1-1/2 in. / 38 mm #6
		Phillips pan-head screws.
INPUT PANELS
	INPUT PANEL	For connecting the power amplifier to the loudspeaker. Also has
		user adjustable controls and PowerSense protection indicator.
	POWERSENSE™ DDP 4 INDICATOR	This LED indicator lights red whenever the PowerSense DDP
		circuitry operates. It indicates the loudspeaker is being overdriven.
	HF LEVEL SWITCH	A 2-position switch used to adjust the volume level of the high
		frequencies for more (+4 dB) or less (FLAT) output.
	PASSIVE / BIAMP SWITCH	Used to select the loudspeaker’s operating mode. Down position
		is for PASSIVE mode (single amplifier) and up position is for BIAMP
		mode (separate LF and HF amplifiers).
		Signal Input: 4 terminal NL4MP jacks. Accept NL4FC in-line
	NEUTRIK SPEAKONS 5	connectors. Used for both PASSIVE and BIAMP modes. Use
		terminals #1 +/- for PASSIVE mode or for BIAMP LF input. Use
		terminals #2 +/- for BIAMP HF input (not used for PASSIVE
		mode). The two jacks are in parallel. 6
11	DUAL 1/4 in. PHONE JACKS 5	Signal Input. Accepts 1/4 in. tip/sleeve (2 conductor) phone plug.
		Tip = +, Sleeve = -. Use either jack for PASSIVE mode. Not used
		for BIAMP mode. The two jacks are in parallel. 6
12	NEUTRIK SPEAKONS 5	Subwoofer signal input. Neutrik NL4MP jacks accept NL4FC in-
		line connectors. Use terminals #1 +/-. Terminals #2 +/- are not
		used. The 2 jacks are in parallel and in parallel with 1/4 in. jacks. 6
13	DUAL 1/4 in. PHONE JACKS 5	Subwoofer signal input. Accepts 1/4 in. tip/sleeve (2 conductor)
		phone plug. Tip = +, Sleeve = -. The two jacks are in parallel
		and in parallel with the Neutrik jacks. 6
	1/4 in. PHONE JACK – HIGH PASS OUTPUT	High-pass output (150 Hz and above) for connecting a full-range
		loudspeaker when using a single amplifier to power both the
		subwoofer and full-range loudspeaker.
OTHER FEATURES
	HANDLES	Use only for carrying and handling - DO NOT USE for mounting or
		suspending the enclosure.
		Protect the corners from damage, act as feet when the enclosure is
	PROTECTIVE CORNERS	freestanding, and mesh with corners on other enclosures when
		stacking so as to position and help stabilize the enclosure on top.
	FEET	Heavy-duty rubber feet. Installed by user on the XLT41E.
	LOGO	Community logo recessed into grille.

Footnotes for Physical Features

1Use ONLY for a horizontal pull direction, i.e. parallel to the enclosure surface where the insert is located. CAUTION: Refer to SECTION 7.4 for further information.

2These points are ONLY for supporting the loudspeaker from the bottom.

DANGER: These points are not intended nor load rated for suspending the loudspeaker.

3Vertical pull is perpendicular to the enclosure surface where the rigging point is located. Horizontal pull is parallel to the enclosure surface where the rigging point is located. CAUTION: Refer to SECTION 7.5 for further information.

4DDP = Dynamic Driver Protection

5Use either type of input jack - Neutrik or 1/4 in. Refer to SECTION 6.2 for further information.

6An unused Neutrik or 1/4 in. jack can be used as a signal output for paralleling to a 2nd loudspeaker. Refer to SECTION 6.3 for further information.

PAGE 10 Community XLT / XLTE Series Owner’s Manual