Avaya 8400B Plus LED Indications

Installation

2-18 Issue 2 November 1996

LED Indications

Two LEDs are located on the top of the 8400B Plus Data Module. One LED is

red, and the other LED is green. These indicate the status of the set during

normal operation, and the result of self-tests when the unit is initially powe red.

When power is first applied to the 8400B Plus Data Module, the unit perform s a

self-test to verify that it is in working order. During the self-test, both LEDs will

remain lit. When the self-test is complete, the green LED will turn off.

■If self-test passed, the red LED will remain on. This indicates that your

8400B Plus Data Module is installed and READY for data

communications operation.

■If self-test failed, the red LED will flash three times, and then remain on.

This indicates a defective unit. Call the Lucent Technologies Technical

Service Center at 1 800 242-2121.

Table2-2 lists all possibl e LED indications. Also refer to Chapter 4 for

troubleshooting guidelines.

Contents

Main Copyright 1996, Avaya Inc. All Rights Reserved Printed in USA Notice Your Responsibility for Your Systems Secu- rity Avaya Fraud Intervention Warranty CE Compliant 1 2 iv 3 4 Page Page About This Document Purpose Organization of This Guide viii How to Order Documentation How to Comment on This Document x Conventions Used ! Security Issues xii NETCON Data Channels PBX Security Measures xiv Lucent Technologies Fraud Intervention Related Documentation xvi Important Safety Instructions !SAVE THESE INSTRUCTIONS xviii Introduction Overview 1-2 Features Physical Description Page Page 1-6 Page Page Installation About the Terminal Device Page Selecting the Correct Installation Procedure Issue 2 November 1996 2-3 Figure 2-1. Components of the US Configuration and the International Configuration CONFIGURATIONS 2-4 What You Need Selecting the Correct Installation Procedure Issue 2 November 1996 2-5 8400B Plus Data Module Installation 2-6 8400B Plus Data Module Selecting an EIA Connector Cord Hardware Installation Connecting the 8400B Plus Data Module to the PBX Wall Jack 2-10 Connecting a Telephone Initial System Checks 2-12 Installation Options With Telephone US Companding Telephone Provides Dialing 2-14 Disable Data Metering Feature Immediate Speakerphone Activation Automatic Speakerphone Activation 2-16 Disable Busyout Feature During Local Loopback Test Changing Installation Options Page 2-18 LED Indications LED Indications Issue 2 November 1996 2-19 Table 2-2. LED Indication Summary LED Red Status of Unit Green 2-20 Table 2-2. LED Indication Summary Continued LED Description LED Red Status of Unit Green Selecting PC Communications Packages 2-22 If You Are Using a PC If You Are Using a Dedicated Terminal Configuration and Operation Operating Modes 3-2 Issuing Commands AT Command Line Prefix Command Buffer Command Line Set Up 3-4 Command Acknowledgment Repeating a Command 3-6 Sample Command Lines Configuration Parameters Parameter Storage and Retrieval 3-8 Page 3-10 Data Operation From Data Mode to Command Mode and Back Dialing a Data Call Storing a Telephone Number 3-12 Automatic Answering Remote Site Use 3-14 Reset and Configuration Recall Sample Command Lines 3-16 A Sample On-Line Session Starting the Session Possible Display Problems Disconnecting a Data Call 3-18 Voice Operations Using the 8400BPlus for Voice Dialing Dialing Instructions Dialing Delay Dialing Pause 3-20 Sample Command Line Page Page Troubleshooting How to Use This Chapter 4-2 Issue 2 November 1996 4-3 Table 4-1. Troubleshooting Guidelines Continued 4-4 Table 4-1. Troubleshooting Guidelines Continued Issue 2 November 1996 4-5 AT&D2 Table 4-1. Troubleshooting Guidelines Continued 4-6 Issue 2 November 1996 4-7 ATDP9,555-1212 ATDP9,,555-1212 ATS8=2 Table 4-1. Troubleshooting Guidelines Continued 4-8 ATS0=1 AT&D0 Table 4-1. Troubleshooting Guidelines Continued Issue 2 November 1996 4-9 ATQ0 ATX4 ATV1 Table 4-1. Troubleshooting Guidelines Continued 4-10 ATEl AT&S0&C0 ATE0 . As you type the ATE0 Table 4-1. Troubleshooting Guidelines Continued A AT Command Set A-2 Page A-4 Page A-6 Page A-8 Page A-10 Page A-12 Page A-14 Page A-16 Page A-18 Page A-20 Page A-22 Page A-24 Page A-26 Page A-28 Page A-30 Page Page B Dial Modifiers B-2 Page B-4 Page B-6 Page Page C S-Registers C-2 Page C-4 Page C-6 Page C-8 Page C-10 Page C-12 Page C-14 Page C-16 Page C-18 Page C-20 Page C-22 Page C-24 Page Page Page C-28 Page C-30 Page C-32 Page C-34 D Isolating Problems Using Loopback Data Tests Data Loopback Test D-2 Performing a Data Loopback Test Local Loopback Test D-4 Performing a Local Loopback Test Local Loopback Test with Self-Test Performing a Local Loopback Test with Self-Test D-6 Remote Loopback Test Performing a Remote Loopback Test D-8 Remote Loopback Test with Self-Test Performing a Remote Loopback Test with Self-Test D-10 Loop-Around Data Test Arrangement Page D-12 Setting Up a Loop-Around Data Test Arrangement Page D-14 Using the Loop-Around Data Test Arrangement Page Page E Quick-Reference Summaries E-2 Page Page Page E-6 Page E-8 Page E-10 Page E-12 Page E-14 Page E-16 Glossary Issue 2 November 1996 GL-1 GL A C D Issue 2 November 1996 GL-3 Glossary E H Page Page Page IN Index Symbols A B D E F G H I L N O P R S T V