Manuals / Bacharach / Household Appliance / Home Security System

Bacharach 2772-0803 manual

Models: 2772-0803

1 49

Page 13

REMOTE INTELLIGENT SENSOR - AREA MONITOR

1.3.8SAMPLE INLET. The sample is brought into the RIS through the short length of black FEP tube and into the optic block. There are two types of input tube; one has a single 0.25 inch (6 mm) diameter tube, the other is a double tube arrange- ment used for systems that monitor aerosols.

NOTE: It is essential that the input tube is correctly fitted, if incorrectly fitted, the measurement will be inaccurate (Figures 2-4 & 2-5).

Instruction 2772-0803

Page 1-3

Page 13

Image 13

Contents

Installation/Operation/Maintenance Rev. 14 - February 2004 CN #3252INSTRUCTION REMOTE INTELLIGENT SENSOR AREA MONITOR 251 Welsh Pool Road Exton, PA Ph 610-363-5450 FaxDeclaration of Conformity Conforms to the following product specifications2 INSTALLATION AND SYSTEM CHECK CONTENTSPage # 1 INTRODUCTION3 SYSTEM OPERATION AND FEATURES CONTENTS continued4 MAINTENANCE AND TROUBLESHOOTING CONTENTS continuedRIS TEST/FAULT PARAMETER LOG SHEET CONTENTS continued5 SYSTEM SPARE PARTS SUPPLEMENT AFEATURES PRODUCT SPECIFICATION PRODUCT SPECIFICATION continued High Flow, all others are Low Flow TABLE #1 RIS CATALOG NUMBERS & DATA1.1 SYSTEM DESCRIPTION 1 INTRODUCTION1.2 BASIC PRINCIPLES Figure 1-1. EnclosureCASSETTE Figure 1-2. Door Open and Cover Removed from Back of DoorMAIN BOARD Page Page REMOTE INTELLIGENT SENSOR - AREA MONITORInstruction 2.2 BATTERY CONNECTION 2 INSTALLATION AND SYSTEM CHECK2.3 MECHANICAL INSTALLATION 2.4 ELECTRICAL INSTALLATIONincluding flanges and connectors 2.5 SYSTEM POWER SUPPLY CONSIDERATION & SELECTION2.6. SAMPLE LINES Figure 2-1. 0 - 1 Volt Conversion 2.8 SYSTEM CHECK 2.7. 0 - 1 VOLT CONVERSION2.7.1 TOOLS & MATERIALS REQUIRED 2.8.1 TAPE CASSETTE LOADING2.8.2 CHECK AND ADJUST SYSTEM 2.8.2.10 Interruption of TEST Mode Cycle. If 2.9 OPTION PCB INSTALLATION WITH Figure 2-2. Hookup for Phase 2 Base Board Terminal StripGAS ALARM FAULT ALARMREMOTE INTELLIGENT SENSOR - AREA MONITOR Figure 2-3. Phase 2 Base Board Terminal StripsInstruction PagePage REMOTE INTELLIGENT SENSOR - AREA MONITORInstruction Instruction REMOTE INTELLIGENT SENSOR - AREA MONITORPage Page REMOTE INTELLIGENT SENSOR - AREA MONITORInstruction 3.1 COMPLETE SAMPLING SEQUENCE 3 SYSTEM OPERATION AND FEATURESFigure 3-1. Sampling Sequence Figure 3-2. No Stain, Both Tracks Used Twice3.2 DENSITY & TIME OPERATING MODES 3.3 CHANGE-OVER FROM DENSITY TO TIME MODE3.4 MINIMUM SAMPLE TIME 3.5 TAPE CASSETTE LIFE3.8 SYSTEM ALARMS 3.10 TEST MODE 3.9 DIAGNOSTICS3.12 USING THE KEYBOARD 3.13 OPTIONAL FEATURESFigure 3-4. Installing Test Card 3.14. PRINTER OPERATION & USE OPTIONAL FEATUREFigure 3-5. Pulling Test Card 3.14.3.2 Print at Intervals. Select by setting Figure 3-6. Switches 2Switch # 1 of SW1 switch bank on the Switch # 2 is not used and is left ‘ONSW2 switches 1 and 2 ‘OFF’ Figure 3-7 Non-Bacharach Printer Interface 4.1 MAINTENANCE GENERAL 4 MAINTENANCE AND TROUBLESHOOTING4.2 VERIFYING THAT A GAS ALARM WAS CAUSED BY GAS 4.4 ADJUSTING LIGHT LEVELS4.6 DISABLING THE ‘DOOR OPEN’ ALARM 4.5 CHECKING AND ADJUSTING SYSTEM FLOW RATE4.7 ADJUSTING THE DOOR SWITCH Figure 4-3. Flow Rate Hookup4.9 RESETTING THE PRINTER OPTION STORAGE 4.10 CLEANING THE SAMPLING INPUT AND OPTICS BLOCK4.8 MEASURING PUMP CURRENT Figure 4-5. Finding Take Up Clutch Figure 4-4. Cleaning Optics blockFigure 4-7. Summary of Gate & Step Values Figure 4-6. Stepping Clamp Vertical4.11 CHANGING A PUMP Figure 4-8. Mechanical Chassis 4.12 EXTERIOR CLEANINGFigure 4-9. Pneumatic Chassis Figure 4-10. Pump Types4.18 TROUBLESHOOTING GENERAL 4.15 INPUT PATH CLEANING4.14 MECHANICAL TIGHTNESS 4.16 PUMP CHECK4.24 DOOR FAULT 4.23 LIGHT FAULTS4.21 EXCESSIVE TAPE USE 4.22 TAPE BREAKAGE5 SYSTEM SPARE PARTS 5.2 SYSTEM POWER SUPPLIES5.1 MODEL DEPENDENT PARTS 5.3 RECOMMENDED SPARES5.4 COMMON PARTS 5.6 SERVICE CENTERS5.5 OPTIONS AND SUPPLIES PennsylvaniaFigure S-2. Pre-4/92 Light Level Access Holes Figure S-1. Test ModeADJUSTING LIGHT LEVELS ON PHASE 1 RIS UNITS A1 EARLIER RIS BASE BOARDSPage S-A2 REMOTE INTELLIGENT SENSOR - AREA MONITORInstruction REMOTE INTELLIGENT SENSOR - AREA MONITOR Figure S-3. Phase 1 Base Board Terminal Strip IdentificationsInstruction Page S-A3Base Board Terminal Strip Identifications Figure S-4. Phase 2 Early VersionREMOTE INTELLIGENT SENSOR - AREA MONITOR Page S-A4