Manuals / Barco / Computer Equipment / Network Router

Barco 26-1302001-00 manual MatrixPRO-II DVI 16x16 Router, User’s Guide

Models: 26-1302001-00

1 43

Download 43 pages 59.99 Kb

Page 38

Image 38

MatrixPRO-II DVI 16x16 Router

________________________________________________________________________

8.After 1 to 2 minutes, and “All Done” message will be shown. Then the firmware upload is completed.

User’s Guide

Rev. 01

Page 38

Image 38

Barco 26-1302001-00 manual MatrixPRO-II DVI 16x16 Router, User’s Guide

Contents

Manual # Revision MatrixPRO-II DVI 16x16 Matrix Router User’s GuideMatrixPRO-II DVI 16x16 Router Guarantee and CompensationFederal Communications FCC Statement User’s GuideFax +32 Company AddressTrademarks 866 374-7878 - Events 24/7 866 469-8036 - Digital Cinema 24/7Use of the Power Cord Operators Safety SummaryPower Source Do not remove panels or coversTurkey RoHS Compliance Terms in This Manual and Equipment MarkingDisposal of the Product wast Electrical and Electronic Equipment AVETISSEMENT中国大陆 RoHS Page ECP # CHANGE HISTORYDate DescriptionTABLE OF CONTENTS 7.2.2 Input and output status 1.2 Shipping 1.1 Key Features1 Introduction 1.3 Notice Of Safe Usage Figure 1-2 Rear panel of MATRIXPRO-II DVI 16 1.4 Physical DescriptionFigure 1-1 Front panel of MATRIXPRO-II DVI 16 Power supplies second power supply is optional, Barco p/n R767420K2 Installation 2.1 Initialization 2.2 EDID ConfigurationINTERFACE CONTROL Read/Write EDID3.1.1 Launching Telnet 3 Control Setup3.1 TCP/IP 3.2 RS-232 3.2.1 Launching HyperTerminal 4.4 FUNCTION mode 4 Front Panel Operation 4.1 LINK mode4.2 UNLINK mode 4.3 PRESET mode “SHIFT ON PRESET”4.4.3 IP Address 4.4.1 Gateway4.4.2 Subnet Mask 4.4.5 UDP Port Number 4.4.8 EDID Configure4.4.4 MAC Address 4.4.6 Video Generator===EDID Configure=== Input 01 Default Default Mode? ===EDID Configure=== Entry EDID Configure? 1 Entry1 Press input 1 key button to enter the EDID Configure Mode ===EDID Configure=== Input 01 Default Default Mode?4.4.9 HDCP Configure HDCP CONFIGURE4.4.11 Control Lock 4.4.12 Reset Mode4.4.10 Baud Rate 5.1 Basic Setup 5 PC Program Operation5.1.1 Connect Info 5.1.3 Video Generator 5.2 EDID setup5.1.2 Channel Name 5.1.4 Control Lock Mode5.3 Operation 5.3.1 Input / output connection 5.3.2 Input channel statusThe disconnected outputs show ‘No Link’ 5.3.3 Output channel statusMatrixPRO-II DVI 16x16 Router User’s Guide6 Web control panel operation Table 7-1 Commands set 7 Commands7.1 Command input structure Table 7-3 Input and output status command examples 7.2 Examples of command inputs 7.2.1 Link input and outputTable 7-2 Link command examples 7.2.2 Input and output status7.2.5 EDID control command 7.2.3 Network setting7.2.4 Monitor output port setting Table 7-4 Network setting command examplesTable 7-6 Monitor output setting command examples 7.2.6 HDCP Setting7.2.7 Baud rate setting for RS-232 Table 7-10 Control lock command examples 7.2.8 Control lock commandTable 7-7 Baud rate setting command examples Table 7-9 Locking type and its ASCII dataAlternatively, you can run Megaboot.exe under Windows XP 8 Firmware updateYou can run Megaboot.exe with Windows 7, as an Administrator MatrixPRO-II DVI 16x16 Router6. Power-On the MATRIXPRO-II DVI MatrixPRO-II DVI 16x16 Router User’s GuideMatrixPRO-II DVI 16x16 Router User’s Guide9 HDCP notes Input power 10 SpecificationsWeight TemperatureReturn Material Authorization RMA 11 WarrantyWarranty Sales Contact 12 Contact InformationBarco Inc Barco N.V