Advanced Network

Main menu Sub-menu			Options
		Closed Caption	On/Off
	Closed Caption Enable		On/Off
	Closed Caption Enable
		Caption Version	CC1/CC2/CC3/CC4
	Standby	Network	On/Off
	Standby	Microphone	On/Off
	Settings	Microphone	On/Off
	Settings	Monitor Out	On/Off
		Monitor Out	On/Off
			Status
			DHCP
5.			IP Address
5.		Wired LAN	Subnet Mask
SYSTEM		Wired LAN	Subnet Mask
SYSTEM			Default Gateway
SETUP:			Default Gateway
SETUP:			DNS Server
Advanced Network			DNS Server
Advanced Network			Apply
	Settings		Status
		Wireless LAN	SSID
		Wireless LAN	IP Address
			IP Address
			Connection Mode
			Account
		Remote Desktop	Password
			Connect
	Reset All Settings
	FAQ-Image and Installation
	FAQ-Features and Service

6.		•	Source
6.		•	Picture Mode
INFORMATION	Current System Status	•	Resolution
	Current System Status	•	Color System
		•	Color System
		•	Equivalent Lamp Hour
		•	Firmware Version

Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

Operation 53

Page 53

Image 53

BenQ MX710, MX711 user manual Advanced Network

Contents

Welcome Table of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Important safety instructions Safety Instructions Locations with an ambient temperature Locations near fire alarmsLocations where the altitudes are higher Confined. Allow at least 50 cm clearance It from the power supplys power outlet InstalledServiced Do not step on the projector or place Introduction Projector featuresIntroduction Shipping contents Lamp cover External control panel Projector exterior viewRear/lower side Projector Controls and functions Keystone/Arrow buttons / Up Down Remote controlTest Mute Operating the Laser pointerMIC/VOL + Numeric buttons Ppr 15º Remote control effective rangeReplacing the remote control batteries Choosing a location Positioning your projectorFront Table Front Ceiling Obtaining a preferred projected image size Projection dimensionsScreen size Distance from screen mm Diagonal Vertical Connection Connecting audio Connecting video source devicesTerminal name Terminal appearance Best About the microphone input Playing sound through the projectorPage Starting up the projector OperationDetails Operation Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarity Use / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Utilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press MODE/ENTER Changing the password If you forget the passwordEntering the password recall procedure To correct keystoning at the bottom of the image Disabling the password functionCorrecting keystone Changing Color Space Switching input signal Selecting the aspect ratio Magnifying and searching for details Adjustments Projectors native resolution in its Displayed in the centerAbout the aspect ratio Screen with a 169 aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to To cancel the timer, perform the following steps Setting the presentation timerSelection Description Top-Left Bottom-Left Top-Right Bottom-Right Remote paging operations Utilizing FAQ functionFreezing the image Hiding the image Locking control keys To activate the High Altitude ModeOperating in a high altitude environment Creating your own startup screen Adjusting the sound level Adjusting the soundAdjusting the microphone volume Turning off the Power On/Off Ring Tone Cable connection Controlling the projector through a LAN environmentIf you are in a Dhcp environment If you are in a non-DHCP environment Highlight Wireless LAN and press MODE/ENTER Wireless connection Controlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Displaying images through Q Presenter Downloading and installing Q PresenterUsing Q Presenter Operation Operation Presenting from a USB Reader Shutting down the projector Direct power offOnce the cooling process finishes, a Power Off Ring Menu system Menu operationMain menu Sub-menu Options Basic Advanced Lamp Mode Normal/Economic Lamp SettingsMessage Equivalent Lamp Hour Advanced Network Description of each menu Temperature Picture ModeManagement Save Settings Display menu Picture menu Function Description Timer System Setup Basic menu Function Description Quick AutoSettings Search Panel Key Settings Security DescriptionBackground Lock Reset All System Setup Advanced menu Function DescriptionBaud Rate Test Pattern Current Features ServiceSystem Status Care of the projector Maintenance Setting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hour Status Message Timing of replacing the lamp Lamp cover loosens Remove the lamp cover from the projector Replacing the lamp Use the handle to slowly pull the lamp out Projector Time will be reset to Connect the power and restart the projectorResetting the lamp timer Light Status & Description Power events IndicatorsLamp events Thermal events Troubleshooting Projector specifications Specifications Mm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25 DimensionsCeiling Mount screw M4 x 8 Max L = 8 mm Unit mm Supported timing for PC input Timing chart 1360 x Supported timing for Hdmi Hdcp input Timing Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Limited warranty Warranty and Copyright informationCopyright Disclaimer FCC statement for United States users Regulation statementsEEC statement for European users Weee directive

Main menu Sub-menu

SETUP:

SSID

Equivalent Lamp Hour

Operation 53