Search, Color Space, Conversion, Presentation, Timer | BenQ MX711

3. SOURCE menu

4. SYSTEM SETUP: Basic menu

	Function	Description
	Quick Auto	See "Switching input signal" on page 26 for details.
	Search	See "Switching input signal" on page 26 for details.
	Search

	Color Space	See "Changing Color Space" on page 26 for details.
	Conversion	See "Changing Color Space" on page 26 for details.
	Conversion
	Presentation	Reminds the presenter to finish the presentation within a certain time
	Timer	frame. See "Setting the presentation timer" on page 32 for details.

	Language	Sets the language for the On-Screen Display (OSD) menus. See "Using
	Language	the menus" on page 22 for details.
		the menus" on page 22 for details.

	Projector	The projector can be installed on a ceiling or behind a screen, or with
	Position	one or more mirrors. See "Choosing a location" on page 14 for details.

		Menu Display Time
		Sets the length of time the OSD will remain active after your last key
	Menu	press. The range is from 5 to 30 seconds in 5-second increments.
	Menu	Menu Position
	Settings	Menu Position
	Settings	Sets the On-Screen Display (OSD) menu position.
		Reminder Message
		Sets the reminder messages on or off.

		Direct Power On
		Allows the projector to turn on automatically once the power is fed
		through the power cord.
		Auto Power Off
		Allows the projector to turn off automatically if no input signal is
	Operation	detected after a set period of time. See "Setting Auto Power Off" on page
	Operation	61 for details.
	Settings	Blank Timer
		Sets the image blank time when the Blank feature is activated, once
		elapsed the image will return to the screen. See "Hiding the image" on
		page 33 for details.
		Sleep Timer
		Sets the auto-shutdown timer. The timer can be set to a value between
		30 minutes and 12 hours.

	Remote	Allows you to enable all the remote receivers or one specific remote
	Receiver	receiver on the projector.

56 Operation

Image 56

BenQ MX711 System Setup Basic menu Function Description Quick Auto, Search, Color Space, Conversion, Presentation, Timer

Contents

Welcome Table of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Important safety instructions Safety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearance Installed It from the power supplys power outletServiced Do not step on the projector or place Introduction Projector featuresIntroduction Shipping contents Lamp cover External control panel Projector exterior viewRear/lower side Controls and functions Projector Keystone/Arrow buttons / Up Down Remote controlTest Operating the Laser pointer MuteMIC/VOL + Numeric buttons Ppr 15º Remote control effective rangeReplacing the remote control batteries Positioning your projector Choosing a locationFront Table Front Ceiling Projection dimensions Obtaining a preferred projected image sizeScreen size Distance from screen mm Diagonal Vertical Connection Connecting video source devices Connecting audioTerminal name Terminal appearance Best Playing sound through the projector About the microphone inputPage Operation Starting up the projectorDetails Operation Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarity Use / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Using a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTER Changing the password If you forget the passwordEntering the password recall procedure To correct keystoning at the bottom of the image Disabling the password functionCorrecting keystone Switching input signal Changing Color Space Magnifying and searching for details Selecting the aspect ratio Projectors native resolution in its Displayed in the center AdjustmentsAbout the aspect ratio Screen with a 169 aspect ratio Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Setting the presentation timer To cancel the timer, perform the following stepsSelection Description Top-Left Bottom-Left Top-Right Bottom-Right Utilizing FAQ function Remote paging operationsFreezing the image Hiding the image To activate the High Altitude Mode Locking control keysOperating in a high altitude environment Creating your own startup screen Adjusting the sound Adjusting the sound levelAdjusting the microphone volume Turning off the Power On/Off Ring Tone Controlling the projector through a LAN environment Cable connectionIf you are in a Dhcp environment If you are in a non-DHCP environment Wireless connection Highlight Wireless LAN and press MODE/ENTER Controlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Displaying images through Q Presenter Downloading and installing Q PresenterUsing Q Presenter Operation Operation Presenting from a USB Reader Shutting down the projector Direct power offOnce the cooling process finishes, a Power Off Ring Menu operation Menu systemMain menu Sub-menu Options Basic Lamp Mode Normal/Economic Lamp Settings AdvancedMessage Equivalent Lamp Hour Advanced Network Description of each menu Picture Mode TemperatureManagement Save Settings Display menu Picture menu Function Description System Setup Basic menu Function Description Quick Auto TimerSettings Search Settings Security Description Panel KeyBackground Lock System Setup Advanced menu Function Description Reset AllBaud Rate Test Pattern Features Service CurrentSystem Status Maintenance Care of the projector Setting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hour Timing of replacing the lamp Status Message Replacing the lamp Lamp cover loosens Remove the lamp cover from the projector Use the handle to slowly pull the lamp out Projector Time will be reset to Connect the power and restart the projectorResetting the lamp timer Indicators Light Status & Description Power eventsLamp events Thermal events Troubleshooting Specifications Projector specifications Dimensions Mm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25Ceiling Mount screw M4 x 8 Max L = 8 mm Unit mm Timing chart Supported timing for PC input Supported timing for Hdmi Hdcp input 1360 x Timing Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Warranty and Copyright information Limited warrantyCopyright Disclaimer Regulation statements FCC statement for United States usersEEC statement for European users Weee directive