Features Service, Current, System, Status

6. INFORMATION menu

	Function	Description
	FAQ-Image
	and
	Installation	Displays possible solutions to problems you may encounter.

	FAQ-
	FAQ-
	Features and
	Service

		Source
		Shows the current signal source.
		Picture Mode
		Shows the selected mode in the PICTURE menu.
	Current	Resolution
	Current	Shows the native resolution of the input signal.
	System	Shows the native resolution of the input signal.
	System	Color System
	Status	Color System
	Status	Shows input system format: NTSC, PAL, SECAM, YUV, or RGB.
		Shows input system format: NTSC, PAL, SECAM, YUV, or RGB.
		Equivalent Lamp Hour
		Displays the number of hours the lamp has been used.
		Firmware Version
		Shows the firmware version of your projector.

Operation 59

Page 59

Image 59

BenQ MX710, MX711 user manual Features Service, Current, System, Status

Contents

Welcome Table of contents Important safety instructions Important safety instructionsSafety Instructions Refer servicing to qualified service personnel Safety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higher Do not step on the projector or place InstalledIt from the power supplys power outlet Serviced Introduction Projector featuresIntroduction Shipping contents Lamp cover External control panel Projector exterior viewRear/lower side Projector Controls and functions Keystone/Arrow buttons / Up Down Remote controlTest Numeric buttons Operating the Laser pointerMute MIC/VOL + Ppr 15º Remote control effective rangeReplacing the remote control batteries Front Ceiling Positioning your projectorChoosing a location Front Table Vertical Projection dimensionsObtaining a preferred projected image size Screen size Distance from screen mm Diagonal Connection Best Connecting video source devicesConnecting audio Terminal name Terminal appearance About the microphone input Playing sound through the projectorPage Operation OperationStarting up the projector Details Fine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the image Use / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Highlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a password Changing the password If you forget the passwordEntering the password recall procedure To correct keystoning at the bottom of the image Disabling the password functionCorrecting keystone Changing Color Space Switching input signal Selecting the aspect ratio Magnifying and searching for details Screen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAdjustments About the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 mode Fine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerTo cancel the timer, perform the following steps Selection Description Hiding the image Utilizing FAQ functionRemote paging operations Freezing the image Creating your own startup screen To activate the High Altitude ModeLocking control keys Operating in a high altitude environment Turning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Adjusting the microphone volume If you are in a non-DHCP environment Controlling the projector through a LAN environmentCable connection If you are in a Dhcp environment Highlight Wireless LAN and press MODE/ENTER Wireless connection Controlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Displaying images through Q Presenter Downloading and installing Q PresenterUsing Q Presenter Operation Operation Presenting from a USB Reader Shutting down the projector Direct power offOnce the cooling process finishes, a Power Off Ring Basic Menu operationMenu system Main menu Sub-menu Options Equivalent Lamp Hour Lamp Mode Normal/Economic Lamp SettingsAdvanced Message Advanced Network Description of each menu Display menu Picture menu Function Description Picture ModeTemperature Management Save Settings Search System Setup Basic menu Function Description Quick AutoTimer Settings Lock Settings Security DescriptionPanel Key Background Test Pattern System Setup Advanced menu Function DescriptionReset All Baud Rate Status Features ServiceCurrent System Care of the projector Maintenance Getting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp information Status Message Timing of replacing the lamp Lamp cover loosens Remove the lamp cover from the projector Replacing the lamp Use the handle to slowly pull the lamp out Projector Time will be reset to Connect the power and restart the projectorResetting the lamp timer Thermal events IndicatorsLight Status & Description Power events Lamp events Troubleshooting Projector specifications Specifications Unit mm DimensionsMm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25 Ceiling Mount screw M4 x 8 Max L = 8 mm Supported timing for PC input Timing chart 1360 x Supported timing for Hdmi Hdcp input Timing Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Disclaimer Warranty and Copyright informationLimited warranty Copyright Weee directive Regulation statementsFCC statement for United States users EEC statement for European users

FAQ-

Features and

Service

Current

System

Status

Equivalent Lamp Hour

Operation 59