Information menu | BenQ W1500 specification

Information menu

This menu shows you the current operating status of the projector.

Some picture adjustments are available only when certain input sources are in use. Unavailable adjustments are not shown on the screen.

	Function	Description
	Source	Shows the current signal source.

	Preset Mode	Shows the selected mode in the Picture -- Basic > Preset Mode menu.

	Resolution	Shows the native resolution of the input source.

	Color System	Shows input system format: NTSC, PAL, SECAM, YUV, or RGB.

	Equivalent Lamp	Shows the total lamp time used.
	Hour	Shows the total lamp time used.
	Hour

	3D Format	Shows the current 3D mode.
	3D Format	3D Format is only available when 3D Mode is enabled.
		3D Format is only available when 3D Mode is enabled.

	Firmware Version	Shows the firmware version of your projector.

Important safety instructions

57

Image 57

BenQ W1500 user manual Information menu

Contents

W1500 Digital Projector Home Cinema Series Table of contents Warranty and Copyright information Table of contents Important safety instructions Important safety instructions Moisture condensation Avoid volatile liquidsDisposal Overview Shipping contents Replacing the remote control batteries Remote control effective rangeCeiling mounting the projector Important safety instructions Projector features Front and upper side view Rear and lower side view Projector exterior viewRS-232 control port Audio L/R input jacks Control panel Controls and functions Remote control Choosing a location Positioning your projector Determine the aspect ratio of your screen, 169 or 43? Obtaining a preferred projected image size Important safety instructions Installation for a 169 ratio screen Projection dimensions Floor Installation Ceiling Installation Installation for a 43 ratio screenScreen dimensions Projection distance D Lowest Highest Screen aspect ratio is 43 and the projected picture is To use the lens shift lever Shifting the projection lens vertically Preparations Connecting with video equipment Connecting Hdmi devices Connecting S-Video or video devices Connecting component-video devices Connect the projector to a computer with a VGA cable Connecting a computer Using the Wireless Transmitter Product specificationSupported timing for wireless Hdmi input timing Mode Refresh rate Hz Frequency kHz Clock MHz Power indicatorMessage and meaning Status Set Wireless Sync to On Wireless transmitter synchronizationWhen the Select Video Source menu displays, select Settings Settings menu, select Add New Video Source Important safety instructions Using the projector Turning the projector onPreparations Sharpen the picture by rotating the focus ring Selecting an input source Using a security cable lock Using the menusUse / to highlight the System Setup menu Securing the projector Setting a password Utilizing the password functionIf you forget the password As the picture indicates, the four arrow keys Changing the password Entering the password recall procedureDisabling the password function Write down the number and turn off your projector Adjusting the projected image Adjusting the projection angleCorrecting picture distortion Selecting a preset mode Using the preset and user modesFine-tuning the selected picture mode Setting the User 1/User 2/User 3 mode Resetting the picture mode Fine-tuning the picture qualityAdjusting Brightness Adjusting Contrast Adjusting Tint Adjusting ColorAdjusting Sharpness Adjusting Flesh Tone Setting a preferred color temperature Setting Black LevelTo set a preferred color temperature Advanced picture quality controls Selecting a Gamma setting Adjusting Brilliant ColorColor Management Setting Film Mode Setting 3D Comb FilterTo leave and save the settings, press MENU/EXIT Adjusting the sound level Adjusting the soundSwitching the left/right audio channels Turning off the Power On/Off Ring Tone About the aspect ratio Selecting the aspect ratio Using the test pattern Freezing the imageMagnifying and searching for details Operating in a high altitude environment To activate High Altitude Mode To display the PIP window Using the remote control Using the OSD menuDisplaying more than one image source simultaneously Watching 3D content Connecting 3D video devicesUsing the 3D menus Personalizing the projector menu display Locking control keysTo lock the keys Turning the projector off On-Screen Display OSD menus Audio SetupOn-Screen Display OSD structure Main menu Sub-menu Options Display System Setup Auto Off Setup AdvancedInformation Function Description Picture -- Basic menu Audio Setup menu Display menu Advanced Setup menu System Setup menu Password High Altitude ModeReset All Settings Test Pattern Information menu Care of the projector Additional information Lamp information Getting to know the lamp hourExtending lamp life Until the next hour lamp warning appears Timing of replacing the lampPress MODE/ENTER to dismiss the message Diminished Replacing the lamp Do not turn on the power with lamp cover removed Connect the power and restart the projector Resetting the lamp timer Indicators Power Temp Lamp Status & DescriptionLamp Status & Description Problem Cause Remedy TroubleshootingYour Blu-ray Disc is not in 3D Format Specifications Ceiling mount installation Dimensions Timing chart Resolution Mode Refresh rate Freq. KHz Clock MHzSupported timing for PC input 1920 x 59.939/60 67.432/67.5 148.35/148.5 Supported timing for Hdmi Hdcp input 1400 x SXGA+60 59.978 65.317 121.750 Timing Resolution Freq. Hz Freq. KHz Dot Clock Freq. MHz Resolution Mode Refresh rate Hz Freq. KHz Clock MHz Video Mode Freq. KHz Freq. Hz Sub-carrier Frequency MHzSupported timing for Video and S-Video inputs Warranty Warranty and Copyright informationCopyright Disclaimer