Manuals / Bissell / Household Appliance / Vacuum Cleaner

Bissell 7901 warranty Carpet Cleaning, Attention Berber Carpet Owners, Caution Do not overwet

Models: 7901

1 24

Download 24 pages 47 Kb

Page 11

Carpet Cleaning

Carpet Cleaning

1.	Plug into a proper outlet and turn the Power and the
1.	SmartTemp switches ON. Wait two minutes for the
	heater to warm up before beginning to clean.
2.	While pressing the trigger, make one slow forward wet
2.	pass and another one back. Let the SmartTemp heated
	formula and DirtLifter Powerbrush do the work for you.
	Caution: Do not overwet.
	Note: Take care not to run over loose objects or
	edges of area rugs. Stalling brush may
	result in premature belt failure.
3.	Release the trigger and make one slow forward and back
3.	pass over the same area to remove any residual dirty water.
4.	Repeat cleaning passes until solution being pulled up
4.	appears clean.
5.	Continue passes without pressing the trigger until you
5.	can’t see any more water being pulled up.
	Note: Both the SmartMix and the clean water
	tank must have liquid in them in order for
	the machine to spray. If one tank is empty
	the machine will not apply either cleaning
	solution or water only.
6.	When the cleaning job is complete refer to the
6.	Maintenance section for machine cleanup and storage

instructions on page 17-19.

ATTENTION BERBER CARPET OWNERS:

Some Berber Carpets have a tendency to fuzz with wear. Repeated strokes in the same area with an ordinary vacuum or deep cleaner may aggravate this condition. Please see Stain Removal instructions on page 12.

11

Image 11

Bissell 7901 Carpet Cleaning, Attention Berber Carpet Owners, Caution Do not overwet, result in premature belt failure

Contents

ProHeat U S E R ’ S G U I D E7901 SERIES 8910 SERIES 6-17Thanks for buying a BISSELL ProHeat Your ProHeat is well made, and we back it with a fullThanks again, from all of us at BISSELL Mark J. Bissell President and Chief Executive OfficerIMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONSGROUNDING INSTRUCTIONS protector 4. HexApplicator ScotchgardProHeat assembly is now complete How to use this guideHow To Put It Together Refer to Assembly Diagram on pageSmartTemp Special Features of your BISSELL ProHeatThe BISSELL SmartClean System SmartMixSmartMix DirtLifter PowerBrushTank-in-Tank Choose the SmartMix setting that fits the cleaning jobRemove the Tank-in-Tank - follow steps 1 and 1. on page 7 and Handle must be in the forward position to reinstallclean hot tap water the lidReadyTools Dial When It’s Time to Empty Tank-in-Tank ContinuedThe Flow Indicator PreTreating Before You Clean CarpetsOperations Machine Preparationheater to warm up before beginning to clean Carpet Cleaningappears clean solution or water onlyBefore treating any stain, follow these pre-treatment steps Stain RemovalUse one of the following methods to Preclean the stain Using BISSELL Tough Stain Precleaner, generously4. Caution Do not overwet AssemblyWhen You’re Done TurboBrushScotchgard protector Applicator Optional 3. may bleed through fabric when wet Cleaning TechniqueImportant - Check Upholstery Tags How to Clean Upholstery and Small AreasPlan your cleaning route to leave an exit path Cleaning Bare FloorsAttach the Bare Floor Tool Use BISSELL Floor Cleansing FormulaMaintenance/Storage section on page Bare Floor Cleaning TechniqueRoutine Maintenance When the cleaning job is complete refer to thePump Belt Replacement Assembly is now complete To Install the Replacement Pump BeltWith the unit still on its side, loop one end of the replacement Re-install the toothed brush belt first onto the red pump pulleySmartTemp Ready Light does not illuminate TroubleshootingPossible Causes RemediesPossible Causes Troubleshooting ContinuedDirtLifter PowerBrush does not turn Cleaner not picking up solutionBISSELL Consumer Services Part Name Replacement parts - BISSELL ProHeatItem Part No BISSELL Consumer Services About Your WarrantyFull One Year Warranty If your BISSELL product should require service