Black & Decker FS110L instruction manual Additional Safety Rules for the Laser, Power Connections

ADDITIONAL SAFETY RULES FOR THE LASER

For your convenience and safety the	FOR LASER SAFETY OBSERVE THE FOLLOWING:
following labels are on your tool.

Fig. A

Fig. B

•LASER LIGHT - DO NOT STARE INTO BEAM, APERTURE, or into a reflection from a mirror-like surface Fig. A & B.

•AVOID EXPOSURE - LASER LIGHT IS EMITTED FROM FRONT GUARD APERTURE. Use of controls or adjustments, or performance of procedures other than those specified herein may result in hazardous laser light exposure.

•DO NOT DISASSEMBLE LASER MODULE. The laser is a CLASS II LASER PRODUCT that can emit laser power up to 1 mW MAX at 650 nm, which could result in exposure with the module disassembled. The laser unit complies with 21 CFR 1040.10 and 1040.11.

•USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

•THE USE OF OPTICAL INSTRUMENTS with this product will increase eye hazard.

•LASER RADIATION, avoid direct eye exposure, serious eye injury can result.

•DO NOT OPERATE IN EXPLOSIVE ATMOSPHERES, such as in the presence of flammable liquids, gases, or dust.

•USE ONLY WITH THE SPECIFICALLY DESIGNATED BATTERIES. Use of any other batteries may create a risk of fire.

•USE ONLY ACCESSORIES that are recommended by the manufacturer for your model.

•ACCESSORIES THAT MAY BE SUITABLE FOR ONE LASER, may create a risk of injury when used on another laser.

•REPAIRS AND SERVICING MUST be performed by a qualified repair facility. Repairs performed by unqualified personnel could result in serious injury.

•DO NOT REMOVE OR DEFACE WARNING LABELS. Removing labels increases the risk of exposure to radiation.

•THIS PRODUCT IS INTENDED for use in a temperature range of 41°F(5°C) - 104°F(40°C).

POWER CONNECTIONS

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the machine to the power line, make sure the switch is in the “OFF” position and be sure that the electric current is of the same characteristics as indicated on the machine. All line connections should make good contact. Running on low voltage will damage the machine.

DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.

MOTOR SPECIFICATIONS

Your machine is wired for 120 volt, 60 HZ alternating current. Before connecting the machine to the power source, make sure the switch is in the “OFF” position.

GROUNDING INSTRUCTIONS

THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRIC SHOCK.

1. All grounded, cord-connected machines:

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This machine is equipped with an electric cord having an equipment- grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician.

Improper connection of the equipment-grounding conductor can result in risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the

equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.

Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the machine is properly grounded.

Use only 3-wire extension cords that have 3-prong grounding type plugs and matching 3-conductor receptacles that accept the machine’s plug, as shown in Fig. C. Repair or replace damaged or worn cord immediately.

2.Grounded, cord-connected machines intended for use on a supply circuit having a nominal rating less than 150 volts:

5