Specifications | Black Box ME759C-RJ45, ME758C-RJ45, May-95 instruction

CHAPTER 1: Specifications

	1. Specifications
Hardware
Required —	Cards can be installed only in MicroRacks (see
	Section 4.1)
Cable Required —	For modem-to-modem line: Two- or four-wire
	unconditioned twisted-pair, 19 to 26 AWG (see
	the Appendix), pinned as shown in Section 4.5
Compliance —	FCC Part 15 Class A, DOC Class/MDC classe A
Interfaces —	Serial:
	ME758C models: EIA/TIA-561 (compatible with
	EIA RS-232 and ITU-TSS [CCITT] V.24);
	ME759C models: EIA RS-232/ITU-TSS V.24
	Line: Two- or four-wire telco;
	Internal: Card-edge for module↔MicroRack
	interconnection
Protocol —	Synchronous or asynchronous
Clock Source —	Internal, external (from DTE) or received (from
	other Card) (user-selectable)
Data Format —	Word length (including start bit, data bits, stop bits,
	and parity bit) must equal 8, 9, 10, or 11 bits (user-
	selectable)
Flow Control —	Transparent to all types of software (X-ON/X-OFF,
	robust X-ON/X-OFF, etc.) flow control; can be set
	to support hardware flow control
Operating Mode —	Two-wire half-duplex or four-wire full- or half-
	duplex (user-selectable)

5

Image 6

Black Box ME759C-RJ45, ME758C-RJ45, May-95, ME759C-RJ11, ME758C-RJ11 manual Specifications

Contents

Multi-Function LD Cards FCC Statements MULTI-FUNCTION LD Card NOM Statements Contents Specifications Indicators DiagnosticsConnectors Weight PowerTemperature Fuse Features IntroductionOverview Introduction Setting the Switches on the Main Module Main-module switches On and OFF settings of the DIP switches Switch S1 Summary S1 Positions 1 through 4 Data-Rate Setting S1 Positions 5 and 6 Clock SourceS1 Position 7 Protocol Switch S2 Summary S2 Position 2 2-Wire vs -Wire OperationS1 Position 8 Carrier-Control Method S2-6 Signaling-Rate Range S2 Position 3 V.52 and V.54 Diagnostic TestingS2 Positions 4 and 5 RTS/CTS Delay S2-7 and S2-8 Word Length Switch S3 Summary S3-1 and S3-2 Input Impedance S3-5 DTE RS-232 Initiation of Local Loopback Test Recommended Impedance SettingsS3-4 Mode Selection S3-6 DTE RS-232 Initiation of Remote Loopback Test Setting the Jumpers on the Interface Module S3-7 and S3-8 Antistream Control Four interface modules Jumper locations Summary of Interface-Module Jumper Functions Line Interface Line Shield Connection to Frame Ground JB2 Serial Interface Signal Ground and Frame Ground JB4 JB5 Installation MicroRacks An Overview MicroRacks’ Power Supply Installing the Multi-Function LD Card in the MicroRack RS-232 Serial Cables and Connectors Pinout of the RS-232 InterfacePinout of the 10-Pin RJ Interface Modem-to-Modem Line Cables and Connectors Line-Cable Pinouts AT&T standard modular color codes Two-pair star wiring for host and slave Cards Multipoint Applications Operation and Diagnostics Status LEDs RTS and CD Indicators Diagnostic Testing Using the Error LED Power-Up V.54 and V.52 Diagnostic Tests Remote Digital Loopback RDL Using the V.52 Bert Test Independently Troubleshooting Calling Your SupplierShipping and Packaging Wire Gauge Capacitance Resistance Appendix Cable Recommendations MULTI-FUNCTION LD Card Copyright 1995. Black Box Corporation. All rights reserved