104
Insert Effect Parameter Functions
Rev0.10
By adding sounds which are out-of-phase with the direct
sound, this effect enhances the definition of the sound, and
pushes it to the forefront.
On/Off OFF, ON
This parameter turns the enhancer effect on/off.
Sens 0 – 100
Adjusts the manner in which the enhancer will be applied
relative to the input signals.
Freq 1.0 – 10.0 kHz
Adjusts the frequency at which the enhancer effect will
begin to be applied. The effect will be made apparent in the
frequencies above the frequency set here.
Mix Level 0 – 100
Adjusts the amount of phase-shifted sound of the range set
by “Frequency” that is to be mixed with the input.
Lo Mix Lvl 0 – 100
Adjusts the amount of phase-shifted sound of the lower
range that is to be mixed with the input. The frequency
range in which the effect is applied is fixed.
Level 0 – 100
Adjusts the volume of the enhanced sound.
A 4-band equalizer.
*
You can use this effect with the following algorithms when “4BAND
EQ” is selected for the 4BAND EQ/WAH “Type” setting.
COSM GTR AMP COSM BASS AMP
COSM COMP GTR COSM COMP BSS
BASS MULTI STEREO MULTI
On/Off OFF, ON
This parameter turns the equalizer effect on/off.
Low Gain -20 – +20 dB
This parameter sets the gain (amount of boost or cut) for the
bass equalizer.
Lo-M Gin -20 – +20 dB
This parameter sets the gain (amount of boost or cut) for the
low-midrange equalizer.
Lo-M F 100 Hz – 10.0 kHz
This parameter sets the central frequency for the low-
midrange equalizer.
Lo-M Q 0.5 – 16
This parameter sets the range of change in gain for the
frequency set by “Lo-M F.” A larger value results in a
narrower range of change.
Hi-M Gin -20 – +20 dB
This parameter sets the gain (amount of boost or cut) for the
high-midrange equalizer.
Hi-M F 100 Hz – 10.0 kHz
This parameter sets the central frequency for the high-
midrange equalizer.
Hi-M Q 0.5 – 16
This parameter sets the range of change in gain for the
frequency set by “Hi-M F.” A larger value results in a
narrower range of change.
Hi Gain -20 – +20 dB
This parameter sets the gain (amount of boost or cut) for the
treble equalizer.
Level -20 – +20 dB
This parameter adjusts the volume after the equalizer stage.
This produces a flanging effect that gives a sort of
“twisting” character to the sound.
* This effect can be used when the MODULATION “Type”
parameter is set to “FLANGER.”
On/Off OFF, ON
This parameter turns the flanger effect on/off.
Rate 0 – 100
Determines the rate of the flanging effect.
Depth 0 – 100
Determines the depth of the flanging effect.
Manual 0 – 100
Adjusts the center frequency at which to apply the effect.
Resonance 0 – 100
Determines the amount of resonance (feedback). Increasing the
value will emphasize the effect, creating a more unusual sound.
Separation 0 – 100
Adjusts the diffusion. The diffusion increases as the value
increases. This will be effective when stereo output is used.
* This effect is obtained with stereo recording (using two tracks).
This is a volume control effect.
By using an expression pedal to control the foot volume,
you can smoothly change the volume of the output sound.
For a detailed explanation, see “When Using an Expression
Pedal” (p. 191).
On/Off OFF, ON
Switches the foot volume on/off.

Enhancer

Equalizer

Flanger

Foot Volume