ERROR MESSAGES

 

 

 

 

 

 

 

 

 

Marks

Error Messages

 

 

Cause/Solution

 

 

 

 

 

 

 

 

 

OK to delete the selected pattern?

This message is displayed when, after selecting a pattern,

 

 

 

 

 

or

is pressed and the pattern is about to be

 

 

 

 

deleted.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OK to delete the setting?

This message appears when

or

is pressed to

 

 

 

 

 

 

 

 

delete the settings for a utility stitch. To delete the selected

 

 

 

 

settings, press

.

 

 

 

 

 

 

 

 

 

 

OK to recall and resume previous memory?

This message appears if the machine is turned off while

 

 

 

 

sewing, then turned on again.

 

 

 

 

 

 

Press

to return the machine to the condition (pattern

 

 

 

 

position and number of stitches) when it was turned off. Follow

 

 

 

 

the procedure described in “If the Thread Breaks During

 

 

 

 

Sewing” on page E-27 to align the needle position and sew the

 

 

 

 

remainder of the pattern.

 

 

 

 

 

 

 

 

 

 

OK to reset the pattern’s border setting, position and/or angle?

This message appears when you try to use the automatic

 

 

 

 

positioning function using the sensor pen with the pattern,

 

 

 

 

rotated or replaced, or with the border pattern. (see page B-83)

 

 

 

 

 

 

 

 

OK to revert to the original position and/or angle?

This message appears when you try to use the automatic

 

 

 

 

positioning function using the sensor pen with the pattern,

 

 

 

 

rotated or replaced. (see page B-83)

 

 

 

 

 

 

 

 

 

 

Preventive maintenance is recommended.

This message is displayed when the machine needs to be

 

 

 

 

maintained. (see page A-19)

 

 

 

 

 

 

 

 

 

 

Raise the buttonhole lever.

This message is displayed when the buttonhole lever is down,

 

 

 

 

a stitch other than a buttonhole is selected, and the

 

 

 

 

“Start/Stop” button or the “Reverse Stitch” button is pushed.

 

 

 

 

 

 

 

 

Remove Dual Feed module from the machine.

This message appears when you try to start embroidering with

 

 

 

 

the dual feed foot attached to the machine. Remove the dual

 

 

 

 

feed foot before entering the embroidery mode. (see page

 

 

 

 

B-68)

 

 

 

 

 

 

 

 

 

 

 

 

Remove Embroidery foot with LED pointer from the machine.

This message appears when you try to start sewing

 

 

 

 

utility/decorative stitch or character pattern with the

 

 

 

 

embroidery foot with the LED pointer attached to the machine.

 

 

 

 

Remove the embroidery foot with the LED pointer before

 

 

 

 

entering the sewing mode. (see page B-61)

 

 

 

 

 

 

 

 

 

Retrieving the pattern. Wait a moment.

This message is displayed when the machine is retrieving a

 

 

 

 

previously saved pattern while in “Embroidery Edit” mode.

 

 

 

 

 

 

 

 

Sensor module error.

This message appears when something is wrong with the

 

 

 

 

sensor unit of the machine. Consult your authorized dealer.

 

 

 

 

 

 

 

 

Set the clock.

This message appears when the time/date is not set. Set

 

 

 

 

time/date. (see page B-22)

 

 

 

 

 

 

 

 

 

 

The bobbin thread is almost empty.

This message is displayed when the bobbin thread is running

 

 

 

 

out.

 

 

 

 

 

 

 

 

 

 

 

 

The bobbin winder safety device has activated. Is the thread

This message is displayed when the bobbin is being wound,

 

 

 

tangled?

and the motor locks because the thread is tangled, etc.

 

 

 

 

 

 

 

 

The carriage of the embroidery unit will move. Keep your

This message appears before embroidery unit moves.

 

 

 

hands etc. away from the carriage.

 

 

 

 

 

 

 

 

 

 

 

 

 

The ending point cannot be selected for this stitch.

This message appears when the function to specify the sewing

 

 

 

 

end point cannot be used with the current stitch. Select other

 

 

 

 

stitch. (see page B-81)

 

 

 

 

 

 

 

 

 

 

The needle position cannot be changed for this stitch.

This message appears when the function to specify the needle

 

 

 

 

drop position cannot be used with the current stitch. Select

 

 

 

 

other stitch. (see page B-81)

 

 

 

 

 

 

 

 

 

 

The needle will move. Keep your hands etc. away from the

This message appears when you touch the point closer than 2

 

 

 

needle area.

cm from the needle drop point with the sensor pen in the

 

 

 

 

sensor function. (see page B-73)

 

 

 

 

 

 

 

 

 

 

The pattern field extends out of the pattern area, repeat setting

This message appears when the specified pattern position

 

 

 

the position and angle using the sensor pen.

extends out of the pattern area. Specify more centered

 

 

 

 

position of the embroidery frame. (see page B-83)

 

 

 

 

 

 

 

 

 

 

A

2

Troubleshooting and Maintenance

Appendix A-35