ERROR MESSAGES

Marks

Error Messages

Cause/Solution

 

 

 

 

 

 

 

 

The pockets are full. Delete a pattern.

This message is displayed when the memory is full and a

 

 

 

 

pattern must be deleted.

 

 

 

 

 

 

 

 

The safety device has been activated.Is the thread tangled? Is

This message is displayed when the motor locks due to

 

 

 

the needle bent?

tangled thread or for other reasons related to thread delivery.

 

 

 

 

 

 

 

The shutoff support mode has been activated. Turn off the

This message appears when the machine is in the shutoff

 

 

 

machine.

support mode. Turn off the machine once to start the machine

 

 

 

again. (see page B-32)

 

 

 

 

 

 

 

 

The “Start/Stop” button does not operate with the foot

This message is displayed when the “Start/Stop” button is

 

 

 

controller attached. Remove the foot controller.

pushed to sew Utility stitches or Character/Decorative stitches

 

 

 

while the foot controller is connected.

 

 

 

 

(This message does not appear when embroidering).

 

 

 

 

 

 

 

 

The upper thread may not be threaded correctly. Thread the

This message is displayed when it seems that the upper

 

 

 

upper thread from the beginning.

thread has not been threaded correctly.

 

 

 

 

 

 

 

 

The USB media was changed. Do not change the USB media

This message is displayed when you attempt to select a

 

 

 

while it is being read.

pattern after the USB media in which the pattern is saved has

 

 

 

been changed.

 

 

 

 

 

 

 

There is no needle plate cover. Attach a needle plate cover.

This message is displayed when the needle plate cover is not

 

 

 

attached.

 

 

 

 

 

 

 

 

This file cannot be used.

This message appears if the file format is incompatible with

 

 

 

 

this machine. Check the list of compatible file formats. (see

 

 

 

 

page S-94)

 

 

 

 

 

 

 

This file exceeds the data capacity and cannot be used. Use a

This message is displayed when the file size exceeds the data

 

 

suitable size file.

capacity of the machine.

 

 

 

 

Confirm the file size and format. (see page S-95)

 

 

 

 

 

 

 

 

This function cannot be used while in the sensor mode.

This message appears when the selected function is not

 

 

 

 

available with the sensor function. (see page B-71)

 

 

 

 

 

 

 

 

This key cannot be used at this time.

This message is displayed when you press

in

 

 

 

 

 

 

the screen other than the Utility Stitch, or press

 

 

 

 

in the screen other than the Utility Stitch or

 

 

 

 

Character/Decorative Stitch.

 

 

 

 

 

 

 

This key does not operate when the needle is down. Raise the

This message is displayed when a key on the LCD display is

 

 

needle and press the key again.

touched while the needle is in the down position.

 

 

 

 

 

 

 

 

This pattern cannot be sewn with this mode.

This message is displayed when the selected stitch is not

 

 

 

 

available for the specific function.

 

 

 

 

 

 

 

This stitch is not “Dual Feed Mode” compatible.

This message appears when the dual feed foot cannot be used

 

 

 

with the current stitch. Select other stitch. (see page B-67)

 

 

 

 

 

 

 

This USB media cannot be used.

This message is displayed when you try to use incompatible

 

 

 

media.

 

 

 

 

 

 

 

This USB media is incompatible.

This message is displayed when you try to use incompatible

 

 

 

USB media. For a list of compatible USB media, visit

 

 

 

 

“ http://solutions.brother.com ”.

 

 

 

 

 

 

 

 

Transmitting by USB

This message is displayed while the USB media is

 

 

 

 

transmitting.

 

 

 

 

 

 

 

Turn off the power and replace the needle plate.

This message is displayed when you try to sew with a stitch

 

 

 

other than a middle needle position stitch while the single-hole

 

 

 

needle plate is installed.

 

 

 

 

This message is displayed when the needle plate is removed

 

 

 

with the machine on or when the machine is turned on and

 

 

 

 

“Embroidery” or “Embroidery Edit” mode is selected (see page

 

 

 

B-24).

 

 

 

 

 

 

 

USB media error

This message is displayed when an error occurs with the USB

 

 

 

media.

 

 

 

 

 

 

 

 

USB media is not loaded. Load USB media.

This message is displayed when you try to recall or save a

 

 

 

 

pattern while no USB media is loaded.

 

 

 

 

 

 

 

 

Use the presser foot lifter button to lower the presser foot.

This message is displayed when a button, such as the

 

 

 

 

“Start/Stop” button, is pushed while the presser foot is raised.

 

 

 

 

 

 

 

 

 

 

 

A-36