Manuals / Bunn / Kitchen Appliance / Coffeemaker

Bunn 428220001E Advanced Adjustments & Optional Settings, 1st RINSE TIME, Ready Degrees

Models: 428220001E

1 20

Download 20 pages 21.87 Kb

Page 15

to toggle between ENGLISH, SPANISH, or

A

ADVANCED ADJUSTMENTS & OPTIONAL SETTINGS

				Press or	to toggle between ENGLISH, SPANISH, or
		ENGLISH
				FRENCH. Press "SELECT" to advance to next screen.
	(-)	SELECT	(+)
				DEFAULT: ENGLISH

	6.	UNITS
	6.	METRIC DONE	ENG
		METRIC DONE	ENG

BASE TEMPERATURE

7. ENABLE DISABLE

BASE TEMPERATURE

A (-) 175°F (+)

BREW LOCKOUT ?

8. NO DONE YES

	9.		READY DEGREES
	9.	(-)	5°F	(+)
		(-)	5°F	(+)

	10.		1st RINSE AIR ON
	10.	-	OFF Secs	+
		-	OFF Secs	+

A		1st RINSE TIME
A	-	60	+

Press for "METRIC" or for "ENGLISH".

Units of measurement will change from °F to °C; oz to milliliters; etc.

DEFAULT: ENGLISH (Flashing)

Press for "ENABLE" or for "DISABLE".

When enabled, will allow different temperatures for reci- pes. NOTE: Will disable BREW LOCKOUT screen. DEFAULT: DISABLE (Flashing)

Press to reduce or to increase base temp. Range: 75° to 205°.

DEFAULT: 175°

Press for "NO" or "YES".

Setting to "YES" will only allow brewing at or above the "READY DEGREES" screen.

DEFAULT: YES (Flashing)

Press to reduce or to increase ready degrees.

Sets the minimum temperature allowable to start a brew cycle. Range: 2° to 20° below the "SET" temperature.

Amount of press out time during auxiliary rinse mode. DEFAULT: OFF (Turning "ON" this screen, will activate the sub screen)

Range: OFF/ 1-60

Auxiliary rinse mode.

DEFAULT: 60

Range: OFF/ 1-4.0

Page 15	42822.1 072810

Image 15

Bunn 428220001E Advanced Adjustments & Optional Settings, FRENCH. Press SELECT to advance to next screen, 1st RINSE TIME

Contents

BUNN-O-MATIC CORPORATION INSTALLATION & OPERATING GUIDE42822.0001E 05/12 2010 Bunn-O-Matic Corporation Page BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTYFOR USE BY TRAINED PERSONNEL ONLY IMPORTANT SAFE GUARDS CONTENTSRECOMMENDED PREVENTIVE MAINTENANCE INTRODUCTION230 VOLT CE Model ELECTRICAL REQUIREMENTSCE REQUIREMENTS 100VPLUMBING REQUIREMENTS Plumbing Hook-UpOptional Drain Hook-Up +/YES NO BREW START INITIAL SET-UPOPERATING CONTROLS RINSECOFFEE BREWING CONTINUED ON NEXT PAGESPECIAL Press to reduce or to increase. DEFAULT 7, Range ADJUSTING BREWING PARAMETERSPress to reduce or to increase. DEFAULT 10, Range OFF Press to reduce or to increase. DEFAULT 5, Range 1-25 seconds11. When brewing has fin- ished, place an empty cup on ADJUSTING BREWING PARAMETERS ContinuedCOFFEE BREWING Continued Press to reduce or to increase. DEFAULT 60, RangeDAILY CLEANING SPRAYHEAD REMOVAL CHECK VALVE REMOVALClean & inspect parts daily Replace if loose, cracked or damaged DEEP CLEAN CYCLE CLEANING TABLETS CLEANING CYCLEDISCONNECT BREWER FROM WATER SUPPLY BEFORE DRAINING WARNING DISCONNECT BREWER FROM POWER SOURCE BEFORE PANEL REMOVALFRONT PANEL REMOVAL AND TANK DRAINING TANK DRAININGADVANCED ADJUSTMENTS & OPTIONAL SETTINGS PROGRAM MODE DEFAULT RANGE LEVELADD RECIPE NAME? ADD COFFEE NAME? ADVANCED ADJUSTMENTS & OPTIONAL SETTINGSto toggle between ENGLISH, SPANISH, or ADVANCED ADJUSTMENTS & OPTIONAL SETTINGSFRENCH. Press SELECT to advance to next screen 1st RINSE TIME2nd RINSE AIR ON 14. NEXTADVANCED ADJUSTMENTS & OPTIONAL SETTINGS 2nd RINSE TIMEADVANCED ADJUSTMENTS & OPTIONAL SETTINGS TEST SWITCHESSkip to HOLD 10 OUNCES ADVANCED ADJUSTMENTS & OPTIONAL SETTINGSOUT = open IN = closed CONTAINER MUSTamount of water captured in the measuring container ADVANCED ADJUSTMENTS & OPTIONAL SETTINGSWhen the test finishes, use the +/- buttons to enter the DISCONNECT BREWER FROM WATER SUPPLY BEFORE DRAININGBREW SETTINGS ADVANCED ADJUSTMENTS & OPTIONAL SETTINGSFACTORY DEFAULTS RESTORE DEFAULTS