Manuals / Bunn / Kitchen Appliance / Coffeemaker

Bunn FMD-1 FMD-2 USER NOTICES Cont, 28964.0000, 28964.0001, PUSH and HOLD BUTTON UNTIL CUP

Models: FMD-1 FMD-2

1 41

Page 3

USER NOTICES (Cont.)

This equipment must be installed to comply with the Basic Plumbing Code of the Building Officials and Code Administrators International, Inc. (BOCA) and the Food Service Sanitation Manual of the Food and Drug Administration (FDA). For models installed outside the U.S.A., comply with the applicable Plumbing /SanitationCode.

00656.0000

00831.0000	27096.0000 FMD-1 ONLY
	28368.0001

PUSH and HOLD BUTTON UNTIL CUP	PUSH and HOLD BUTTON UNTIL CUP
IS 2/3 FULL, THEN RELEASE	IS 2/3 FULL, THEN RELEASE
28964.0000	28964.0001
	28964.0001

3	29112 011906

Page 3

Image 3

Bunn FMD-1 FMD-2 USER NOTICES Cont, 28964.0000, 28964.0001, PUSH and HOLD BUTTON UNTIL CUP, IS 2/3 FULL, THEN RELEASE

Contents

S/N FMD0013000-UP FMD-1 FMD-2BUNN-O-MATICCORPORATION POST OFFICE BOX SPRINGFIELD, ILLINOIS PHONE 217 529-6601 FAXWARRANTY INTRODUCTIONUSER NOTICES PUSH and HOLD BUTTON UNTIL CUP USER NOTICES Cont28964.0000 28964.0001PLUMBING REQUIREMENTS INITIAL SET-UPELECTRICAL REQUIREMENTS ELECTRICAL HOOK-UPRUNNING A RINSE SEQUENCE RINSE TIMER FMD-2 ONLYINITIAL FILL & HEAT LIQUID LEVEL CONTROLCOLD BEVERAGE SET-UP OPTIONAL FMD-2 ONLY CLEANINGADJUSTMENTS HOPPER MOTOR SPEED ADJUSTMENT FMD-1DRAINING THE HOT WATER TANK HOPPER MOTOR SPEED PROGRAMING FMD-2REMEDY TROUBLESHOOTINGPROBLEM PROBABLE CAUSEREMEDY TROUBLESHOOTING contPROBLEM PROBABLE CAUSERefer to Service - Control Board and TROUBLESHOOTING contPROBLEM Refer to Service - Level Control BoardRefer to Operation - Rinse Timer PROBLEMTROUBLESHOOTING cont for test procedures. See pagePROBLEM Dispenser is making unusualREMEDY AUGER DRIVE COMPONENTS FMD-1 SERVICECOMPONENT ACCESS ContentsSERVICE AUGER DRIVE COMPONENTS - FMD-1 CONTSERVICE cont AUGER DRIVE COMPONENTS - FMD-1 contAUGER DRIVE COMPONENTS - FMD-2 19. Hopper Support plate AUGER DRIVE COMPONENTS - FMD-2 CONTSERVICE cont FIG. 5 AUGER DRIVE & HOPPER DISASSEMBLYSERVICE cont AUGER DRIVE COMPONENTS - FMD-2 contFIG. 7 AUGER MOTOR TERMINALS SERVICE cont9. Using four #8-32 screws install new auger motor AUGER DRIVE COMPONENTS - FMD-2 contSERVICE cont BALLAST - FMD-1 & FMD-2 contCONTROL BOARD - FMD-2 ONLY SERVICE contCONTROL THERMOSTAT - FMD-1 & FMD-2 cont SERVICE cont CONTROL BOARD - FMD-2 ONLY CONTFMD-1 SERVICE contFIG.14 DISPENSE SWITCH CONTROL BOARD - FMD-2 ONLY CONTSERVICE cont DISPENSE SWITCHS - FMD-1 & FMD-2 contFAN - FMD-1 & FMD-2 SERVICE contDISPENSE SWITCHS - FMD-1 & FMD-2 cont voltage across the disconnected harness wires FMD-2SERVICE cont Disconnect the red and white wires FMD-1SERVICE cont FROTHER AND WHIPPER MOTOR - FMD-1 shown & FMD-2 contSERVICE cont HOPPER DRIVE BOARD - FMD-1 ONLYHOPPER DRIVE BOARD - FMD-1 ONLY cont SERVICE contFIG. 24 INCREASE/DECREASE SWITCH LAMP REPLACEMENT Refer to Fig SERVICE contStarter W/Socket SERVICE cont LAMP REPLACEMENT Refer to Fig.24contLAMP STARTER and SOCKET Refer to Fig. 25 Location LEVEL CONTROL BOARD AND LEVEL PROBE - FMD-1 ONLYSERVICE cont LEVEL CONTROL BOARD AND LEVEL PROBE - FMD-1 ONLY contLocation RINSE/RUN SWITCH - FMD-1FIG. 30 RINSE/RUN SWITCH FIG. 28 LIMIT THERMOSTATRINSE/RUN SWITCH - FMD-1 CONT RINSE/RUN SWITCH - FMD-2SERVICE cont SOLENOID VALVE COLD WATER OPTIONALFMD-2 ONLY SERVICE contLocation FMD-2 SERVICE contLocation FMD-1SOLENOID VALVE INLET - FMD-1 & FMD-2 SOLENOID VALVE DISPENSE - FMD-1 & FMD-2 contFIG. 38 INLET SOLENOID VALVE SERVICE contLocation SOLENOID VALVE INLET - FMD-1 & FMD-2 contFIG. 40 TANK HEATER SERVICE contBLK to Limit TANK HEATER SWITCH - FMD-1 shown & FMD-2TANK HEATER - FMD-1 shown & FMD-2 cont SERVICE contSERVICE cont TRANSFORMER - FMD-2 ONLYWHI/GRN - T7 WHI/BLK - T12120 VOLTS A C - 2 WIRE 120/208-240 VOLTS AC - 3WIRE SINGLE PHASE SCHEMATIC WIRING DIAGRAM FMD-1SINGLE PHASE, 60 HZ SCHEMATIC WIRING DIAGRAM FMD-2120/208-240 VOLTS AC - 3 WIRE 120 VOLTS AC - 2 WIRE

USER NOTICES (Cont.)

PUSH and HOLD BUTTON UNTIL CUP

IS 2/3 FULL, THEN RELEASE

28964.0000

28964.0001