Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems setup guide Rack Mounting the 6C105

Models: 6C105

1 38

Download 38 pages 14.91 Kb

Page 24

3.2.3Rack Mounting the 6C105

Chapter 3: 6C105 Setup

3.2.3Rack Mounting the 6C105

The 6C105 can be mounted in a standard 19-inch equipment rack.

If the rack is not secured to the floor, it is recommended that

!the chassis be installed in the bottom half of the rack. This

CAUTION	prevents the rack from being top heavy.

Read Chapter 2 in this manual before completing the following

!procedure.

CAUTION

Two people may be required to lift the chassis into place.

The chassis is secured with ten screws, ﬁve on each side. Using the screws provided with the equipment rack, secure the 6C105 to the rack, starting with the bottom holes and working up, as shown in Figure 3-2.

Rack Mounting Holes (5)

Rack Mounting

Screws (5)

1	2	3	4	5	PS1	PS2
						6C405

Rack Mounting Holes (5)

Rack Mounting Screws (5)

Figure 3-2 Rack Mounting the 6C105

3-4	6C105 Overview and Setup Guide

Image 24

Cabletron Systems setup guide Rack Mounting the 6C105

Contents

6C105 SmartSwitch 6000 Overview and Setup Guide 9032016-046C405 Page Only qualiﬁed personnel should perform installation procedures 6C105 Overview and Setup GuideFCC NOTICE 6C105 Overview and Setup Guide DOC NOTICEVCCI NOTICE CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENTEXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY 6C105 Overview and Setup GuideCABLETRON SOFTWARE PROGRAM LICENSE UNITED STATES GOVERNMENT RESTRICTED RIGHTS6C105 Overview and Setup Guide DECLARATION OF CONFORMITYCONTENTS INSTALLATION REQUIREMENTS ANDSPECIFICATIONS 6C105 SETUPContents 6C105 Overview and Setup Guide1.1 USING THIS GUIDE CHAPTER INTRODUCTION1.2 STRUCTURE OF THIS GUIDE 1.4 USING THE 6C105 MANUAL SET 1.3 DOCUMENT CONVENTIONSChapter 1 Introduction 1.5 GETTING HELP 1.6 OVERVIEW Figure 1-1 The 6C105 Chassis with Redundant Power Supplies1.7 FEATURES Auto-Ranging Power Supplies Hot SwappingThe 6C105 Cooling System Rack Mountable ChassisCHAPTER INSTALLATION REQUIREMENTS AND SPECIFICATIONS 2.1 SITE GUIDELINES2.2 CONFIGURATION GUIDELINES 2.3 OPERATING SPECIFICATIONS2.3.1 Physical Speciﬁcations H x 44.04 W x 35.56 D cm2.3.2 Power Supply Requirements 2.4.1 Power Supply LEDs2.4 LEDs 100 to 125 Vac, 6.2 Amps6C105 Overview and Setup Guide Table 2-1 Power Supply LED States and Their DeﬁnitionsFigure 2-1 Power Supply LEDs LEDs2.4.2 Fan Tray LED Chapter 2 Installation Requirements and Speciﬁcations6C105 Overview and Setup Guide Fan Tray LEDCHAPTER 6C105 SETUP 3.1 UNPACKING THE 6C1053.2 SETTING UP THE 6C105 3.2.1 Installation Order3.2.2 Installing the Cable Management Bar 3.2.3 Rack Mounting the 6C105 3.2.4 Attaching the Electrostatic Discharge Wrist Strap Figure 3-3 ESD Grounding Receptacle3.2.5 Installing a Power Supply Module 4. Slide the power supply module into the slot labeled PS1 as follows Figure 3-4 Installing the Power Supply Modules Slotted Screw3.2.6 Installing 6C105 Interface Modules engages the backplane connectorsChapter 3 6C105 Setup 6C105 Overview and Setup GuideFigure 3-5 Installing a Module Connector3.3 POWERING UP A 6C105 WITH AC POWER SUPPLIES 3.4 POWERING UP A 6C105 WITH DC POWER SUPPLIESChapter 3 6C105 Setup DC Power Supply Requirement for Each Supply6C105 Overview and Setup Guide 3-123.4.1 Connecting a 6C205-2 to a 48/60 VDC Power Source 3.5 REMOVING AND REINSTALLING THE FAN TRAY 3.5.1 Removing the Fan Tray3.5.2 Reinstalling the Fan Tray In the following step ensure that you do not force the fan trayinto place, as it may damage the unit 4. Slide the fan tray forward until the faceplate of the tray is flush with the face of the 6C105. If there is any strong resistance, remove the fan tray and reinsert it Removing and Reinstalling the Fan Tray 6C105 Overview and Setup GuideFigure 3-9 Reinstalling the Fan Tray 3-17Chapter 3 6C105 Setup 6C105 Overview and Setup Guide3-18