Manuals
/
Cabletron Systems
/
Computer Equipment
/
Switch
Cabletron Systems
setup guide 6C105 Setup, 3-18, 6C105 Overview and Setup Guide
Models:
6C105
1
38
38
Download
38 pages
14.91 Kb
31
32
33
34
35
36
37
38
<
>
Specifications
Install
Warranty
Configuration Guidelines
Connecting a 6C205-2 to a 48/60 VDC Power Source
6C105 SmartSwitch 6000 Overview and Setup Guide
1 The 6C105 Chassis with Redundant Power Supplies
engages the backplane connectors
Features
Using This Guide
Page 38
Image 38
Chapter 3:
6C105 Setup
3-18
6C105 Overview and Setup Guide
Page 37
Page 38
Image 38
Page 37
Contents
6C405
6C105 SmartSwitch 6000 Overview and Setup Guide
9032016-04
Page
FCC NOTICE
Only qualified personnel should perform installation procedures
6C105 Overview and Setup Guide
VCCI NOTICE
6C105 Overview and Setup Guide
DOC NOTICE
CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT
CABLETRON SOFTWARE PROGRAM LICENSE
EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY
6C105 Overview and Setup Guide
UNITED STATES GOVERNMENT RESTRICTED RIGHTS
6C105 Overview and Setup Guide
DECLARATION OF CONFORMITY
SPECIFICATIONS
CONTENTS
INSTALLATION REQUIREMENTS AND
6C105 SETUP
Contents
6C105 Overview and Setup Guide
1.2 STRUCTURE OF THIS GUIDE
1.1 USING THIS GUIDE
CHAPTER INTRODUCTION
Chapter 1 Introduction
1.4 USING THE 6C105 MANUAL SET
1.3 DOCUMENT CONVENTIONS
1.5 GETTING HELP
1.6 OVERVIEW
Figure 1-1 The 6C105 Chassis with Redundant Power Supplies
1.7 FEATURES
The 6C105 Cooling System
Auto-Ranging Power Supplies
Hot Swapping
Rack Mountable Chassis
CHAPTER INSTALLATION REQUIREMENTS AND SPECIFICATIONS
2.1 SITE GUIDELINES
2.2 CONFIGURATION GUIDELINES
2.3 OPERATING SPECIFICATIONS
2.3.1 Physical Specifications
H x 44.04 W x 35.56 D cm
2.4 LEDs
2.3.2 Power Supply Requirements
2.4.1 Power Supply LEDs
100 to 125 Vac, 6.2 Amps
Figure 2-1 Power Supply LEDs
6C105 Overview and Setup Guide
Table 2-1 Power Supply LED States and Their Definitions
LEDs
6C105 Overview and Setup Guide
2.4.2 Fan Tray LED
Chapter 2 Installation Requirements and Specifications
Fan Tray LED
CHAPTER 6C105 SETUP
3.1 UNPACKING THE 6C105
3.2 SETTING UP THE 6C105
3.2.1 Installation Order
3.2.2 Installing the Cable Management Bar
3.2.3 Rack Mounting the 6C105
3.2.4 Attaching the Electrostatic Discharge Wrist Strap
Figure 3-3 ESD Grounding Receptacle
3.2.5 Installing a Power Supply Module
4. Slide the power supply module into the slot labeled PS1 as follows
Figure 3-4 Installing the Power Supply Modules
Slotted Screw
3.2.6 Installing 6C105 Interface Modules
engages the backplane connectors
Figure 3-5 Installing a Module
Chapter 3 6C105 Setup
6C105 Overview and Setup Guide
Connector
3.3 POWERING UP A 6C105 WITH AC POWER SUPPLIES
3.4 POWERING UP A 6C105 WITH DC POWER SUPPLIES
6C105 Overview and Setup Guide
Chapter 3 6C105 Setup
DC Power Supply Requirement for Each Supply
3-12
3.4.1 Connecting a 6C205-2 to a 48/60 VDC Power Source
3.5 REMOVING AND REINSTALLING THE FAN TRAY
3.5.1 Removing the Fan Tray
into place, as it may damage the unit
3.5.2 Reinstalling the Fan Tray
In the following step ensure that you do not force the fan tray
4. Slide the fan tray forward until the faceplate of the tray is flush with the face of the 6C105. If there is any strong resistance, remove the fan tray and reinsert it
Figure 3-9 Reinstalling the Fan Tray
Removing and Reinstalling the Fan Tray
6C105 Overview and Setup Guide
3-17
3-18
Chapter 3 6C105 Setup
6C105 Overview and Setup Guide