Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems setup guide SETTING UP THE 6C105, Installation Order

Models: 6C105

1 38

Download 38 pages 14.91 Kb

Page 22

Chapter 3: 6C105 Setup

3.2SETTING UP THE 6C105

The following sections describe the procedures that must be followed to complete the installation of the 6C105.

3.2.1Installation Order

Once a suitable site has been chosen, the 6C105 can be installed. The chassis can be freestanding or rack mounted.

It is recommended that the 6C105 installation proceed in this order:

1.Install the cable management bar.

2.Mount the chassis to a 19-inch rack or other secure location.

3.Attach the Electrostatic Discharge Wrist Strap.

4.Install the Power Supply Module(s).

5.Install the Interface Modules.

3-2	6C105 Overview and Setup Guide

Image 22

Cabletron Systems setup guide SETTING UP THE 6C105, Installation Order

Contents

9032016-04 6C105 SmartSwitch 6000 Overview and Setup Guide6C405 Page 6C105 Overview and Setup Guide Only qualiﬁed personnel should perform installation proceduresFCC NOTICE VCCI NOTICE 6C105 Overview and Setup GuideDOC NOTICE CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENTCABLETRON SOFTWARE PROGRAM LICENSE EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY6C105 Overview and Setup Guide UNITED STATES GOVERNMENT RESTRICTED RIGHTS6C105 Overview and Setup Guide DECLARATION OF CONFORMITYSPECIFICATIONS CONTENTSINSTALLATION REQUIREMENTS AND 6C105 SETUPContents 6C105 Overview and Setup GuideCHAPTER INTRODUCTION 1.1 USING THIS GUIDE1.2 STRUCTURE OF THIS GUIDE 1.3 DOCUMENT CONVENTIONS 1.4 USING THE 6C105 MANUAL SETChapter 1 Introduction 1.5 GETTING HELP 1.6 OVERVIEW Figure 1-1 The 6C105 Chassis with Redundant Power Supplies1.7 FEATURES The 6C105 Cooling System Auto-Ranging Power SuppliesHot Swapping Rack Mountable ChassisCHAPTER INSTALLATION REQUIREMENTS AND SPECIFICATIONS 2.1 SITE GUIDELINES2.2 CONFIGURATION GUIDELINES 2.3 OPERATING SPECIFICATIONS2.3.1 Physical Speciﬁcations H x 44.04 W x 35.56 D cm2.4 LEDs 2.3.2 Power Supply Requirements2.4.1 Power Supply LEDs 100 to 125 Vac, 6.2 AmpsFigure 2-1 Power Supply LEDs 6C105 Overview and Setup GuideTable 2-1 Power Supply LED States and Their Deﬁnitions LEDs6C105 Overview and Setup Guide 2.4.2 Fan Tray LEDChapter 2 Installation Requirements and Speciﬁcations Fan Tray LEDCHAPTER 6C105 SETUP 3.1 UNPACKING THE 6C1053.2 SETTING UP THE 6C105 3.2.1 Installation Order3.2.2 Installing the Cable Management Bar 3.2.3 Rack Mounting the 6C105 3.2.4 Attaching the Electrostatic Discharge Wrist Strap Figure 3-3 ESD Grounding Receptacle3.2.5 Installing a Power Supply Module 4. Slide the power supply module into the slot labeled PS1 as follows Figure 3-4 Installing the Power Supply Modules Slotted Screw3.2.6 Installing 6C105 Interface Modules engages the backplane connectorsFigure 3-5 Installing a Module Chapter 3 6C105 Setup6C105 Overview and Setup Guide Connector3.3 POWERING UP A 6C105 WITH AC POWER SUPPLIES 3.4 POWERING UP A 6C105 WITH DC POWER SUPPLIES6C105 Overview and Setup Guide Chapter 3 6C105 SetupDC Power Supply Requirement for Each Supply 3-123.4.1 Connecting a 6C205-2 to a 48/60 VDC Power Source 3.5 REMOVING AND REINSTALLING THE FAN TRAY 3.5.1 Removing the Fan TrayIn the following step ensure that you do not force the fan tray 3.5.2 Reinstalling the Fan Trayinto place, as it may damage the unit 4. Slide the fan tray forward until the faceplate of the tray is flush with the face of the 6C105. If there is any strong resistance, remove the fan tray and reinsert it Figure 3-9 Reinstalling the Fan Tray Removing and Reinstalling the Fan Tray6C105 Overview and Setup Guide 3-176C105 Overview and Setup Guide Chapter 3 6C105 Setup3-18