Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems setup guide 6C105 Setup, DC Power Supply Requirement for Each Supply, 3-12

Models: 6C105

1 38

Download 38 pages 14.91 Kb

Page 32

DC Power Supply Requirement for Each Supply

Chapter 3: 6C105 Setup

ON/OFF

DC Input Power Strip

2016_99

Figure 3-6 Power Supply DC ON/OFF Switch and DC Input Power Strip

ONLY QUALIFIED PERSONNEL SHOULD PERFORM THESE INSTALLATION PROCEDURES.

TO REDUCE THE RISK OF ELECTRIC SHOCK OR ENERGY HAZARDS:

•CONNECT TO A RELIABLY GROUNDED 48/60 VDC SELV SOURCE.

•ENSURE THE BRANCH CIRCUIT OVERCURRENT PROTECTION IS RATED AT A MINIMUM

OF 25 A.

•USE 10 AWG SOLID COPPER CONDUCTORS ONLY.

•ENSURE THAT A READILY ACCESSIBLE DISCONNECT DEVICE THAT IS SUITABLY APPROVED AND RATED, IS INCORPORATED IN THE FIELD WIRING.

TO BE INSTALLED IN A RESTRICTED ACCESS AREA IN ACCORDANCE WITH THE NEC OR THE AUTHORITY HAVING JURISDICTION.

DC Power Supply Requirement for Each Supply

Each DC power supply input requires either a 48 VDC or 60 VDC power source, rated at a minimum of 17 Amps.

3-12	6C105 Overview and Setup Guide

Image 32

Cabletron Systems 6C105 Setup, DC Power Supply Requirement for Each Supply, 3-12, 6C105 Overview and Setup Guide

Contents

6C405 6C105 SmartSwitch 6000 Overview and Setup Guide9032016-04 Page FCC NOTICE Only qualiﬁed personnel should perform installation procedures6C105 Overview and Setup Guide 6C105 Overview and Setup Guide DOC NOTICEVCCI NOTICE CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENTEXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY 6C105 Overview and Setup GuideCABLETRON SOFTWARE PROGRAM LICENSE UNITED STATES GOVERNMENT RESTRICTED RIGHTS6C105 Overview and Setup Guide DECLARATION OF CONFORMITYCONTENTS INSTALLATION REQUIREMENTS ANDSPECIFICATIONS 6C105 SETUPContents 6C105 Overview and Setup Guide1.2 STRUCTURE OF THIS GUIDE 1.1 USING THIS GUIDECHAPTER INTRODUCTION Chapter 1 Introduction 1.4 USING THE 6C105 MANUAL SET1.3 DOCUMENT CONVENTIONS 1.5 GETTING HELP 1.6 OVERVIEW Figure 1-1 The 6C105 Chassis with Redundant Power Supplies1.7 FEATURES Auto-Ranging Power Supplies Hot SwappingThe 6C105 Cooling System Rack Mountable ChassisCHAPTER INSTALLATION REQUIREMENTS AND SPECIFICATIONS 2.1 SITE GUIDELINES2.2 CONFIGURATION GUIDELINES 2.3 OPERATING SPECIFICATIONS2.3.1 Physical Speciﬁcations H x 44.04 W x 35.56 D cm2.3.2 Power Supply Requirements 2.4.1 Power Supply LEDs2.4 LEDs 100 to 125 Vac, 6.2 Amps6C105 Overview and Setup Guide Table 2-1 Power Supply LED States and Their DeﬁnitionsFigure 2-1 Power Supply LEDs LEDs2.4.2 Fan Tray LED Chapter 2 Installation Requirements and Speciﬁcations6C105 Overview and Setup Guide Fan Tray LEDCHAPTER 6C105 SETUP 3.1 UNPACKING THE 6C1053.2 SETTING UP THE 6C105 3.2.1 Installation Order3.2.2 Installing the Cable Management Bar 3.2.3 Rack Mounting the 6C105 3.2.4 Attaching the Electrostatic Discharge Wrist Strap Figure 3-3 ESD Grounding Receptacle3.2.5 Installing a Power Supply Module 4. Slide the power supply module into the slot labeled PS1 as follows Figure 3-4 Installing the Power Supply Modules Slotted Screw3.2.6 Installing 6C105 Interface Modules engages the backplane connectorsChapter 3 6C105 Setup 6C105 Overview and Setup GuideFigure 3-5 Installing a Module Connector3.3 POWERING UP A 6C105 WITH AC POWER SUPPLIES 3.4 POWERING UP A 6C105 WITH DC POWER SUPPLIESChapter 3 6C105 Setup DC Power Supply Requirement for Each Supply6C105 Overview and Setup Guide 3-123.4.1 Connecting a 6C205-2 to a 48/60 VDC Power Source 3.5 REMOVING AND REINSTALLING THE FAN TRAY 3.5.1 Removing the Fan Trayinto place, as it may damage the unit 3.5.2 Reinstalling the Fan TrayIn the following step ensure that you do not force the fan tray 4. Slide the fan tray forward until the faceplate of the tray is flush with the face of the 6C105. If there is any strong resistance, remove the fan tray and reinsert it Removing and Reinstalling the Fan Tray 6C105 Overview and Setup GuideFigure 3-9 Reinstalling the Fan Tray 3-173-18 Chapter 3 6C105 Setup6C105 Overview and Setup Guide