Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems setup guide POWERING UP A 6C105 WITH AC POWER SUPPLIES

Models: 6C105

1 38

Download 38 pages 14.91 Kb

Page 31

3.3POWERING UP A 6C105 WITH AC POWER SUPPLIES

Powering Up a 6C105 with AC Power Supplies

3.3POWERING UP A 6C105 WITH AC POWER SUPPLIES

To power up a 6C105 with ac power supply modules proceed as follows:

NOTE

If two power supplies are installed, repeat the following procedure for each supply.

1.Plug one end of the power cord (supplied with the power supply) into the ac power socket on the bottom of the power supply.

2.Plug the other end of the power cord into an ac receptacle. Turn on the power supply using the switch located above the power socket.

3.Ensure that the Power LED is green.

4.Ensure that all fans in the fan tray unit are operating properly when power is received from the power supply modules (fan tray LED will be green).

If you experience any problems during the installation of the 6C105, contact the Cabletron Systems Global Call Center for assistance.

3.4POWERING UP A 6C105 WITH DC POWER SUPPLIES

This section provides information on how to connect the 6C205-2 DC power supply to 48 or 60 VDC (48/60 VDC) power sources. The 6C205-2 is installed and functions the same as the ac power supplies for the 6C105. The 6C205-2 power supply has an on/off switch and an input power strip, and is rated at 510 watts. The on/off power switches and input power strips are similar to the ones shown in Figure 3-6.

NOTE

The on/off switch of the 6C205-2 power supply contains a 30 Amp circuit breaker.

6C105 Overview and Setup Guide

3-11

Image 31

Cabletron Systems setup guide POWERING UP A 6C105 WITH AC POWER SUPPLIES, POWERING UP A 6C105 WITH DC POWER SUPPLIES

Contents

9032016-04 6C105 SmartSwitch 6000 Overview and Setup Guide6C405 Page 6C105 Overview and Setup Guide Only qualiﬁed personnel should perform installation proceduresFCC NOTICE CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT 6C105 Overview and Setup GuideDOC NOTICE VCCI NOTICEUNITED STATES GOVERNMENT RESTRICTED RIGHTS EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY6C105 Overview and Setup Guide CABLETRON SOFTWARE PROGRAM LICENSEDECLARATION OF CONFORMITY 6C105 Overview and Setup Guide6C105 SETUP CONTENTSINSTALLATION REQUIREMENTS AND SPECIFICATIONS6C105 Overview and Setup Guide ContentsCHAPTER INTRODUCTION 1.1 USING THIS GUIDE1.2 STRUCTURE OF THIS GUIDE 1.3 DOCUMENT CONVENTIONS 1.4 USING THE 6C105 MANUAL SETChapter 1 Introduction 1.5 GETTING HELP Figure 1-1 The 6C105 Chassis with Redundant Power Supplies 1.6 OVERVIEW1.7 FEATURES Rack Mountable Chassis Auto-Ranging Power SuppliesHot Swapping The 6C105 Cooling System2.1 SITE GUIDELINES CHAPTER INSTALLATION REQUIREMENTS AND SPECIFICATIONS2.3 OPERATING SPECIFICATIONS 2.2 CONFIGURATION GUIDELINESH x 44.04 W x 35.56 D cm 2.3.1 Physical Speciﬁcations100 to 125 Vac, 6.2 Amps 2.3.2 Power Supply Requirements2.4.1 Power Supply LEDs 2.4 LEDsLEDs 6C105 Overview and Setup GuideTable 2-1 Power Supply LED States and Their Deﬁnitions Figure 2-1 Power Supply LEDsFan Tray LED 2.4.2 Fan Tray LEDChapter 2 Installation Requirements and Speciﬁcations 6C105 Overview and Setup Guide3.1 UNPACKING THE 6C105 CHAPTER 6C105 SETUP3.2.1 Installation Order 3.2 SETTING UP THE 6C1053.2.2 Installing the Cable Management Bar 3.2.3 Rack Mounting the 6C105 Figure 3-3 ESD Grounding Receptacle 3.2.4 Attaching the Electrostatic Discharge Wrist Strap3.2.5 Installing a Power Supply Module 4. Slide the power supply module into the slot labeled PS1 as follows Slotted Screw Figure 3-4 Installing the Power Supply Modulesengages the backplane connectors 3.2.6 Installing 6C105 Interface ModulesConnector Chapter 3 6C105 Setup6C105 Overview and Setup Guide Figure 3-5 Installing a Module3.4 POWERING UP A 6C105 WITH DC POWER SUPPLIES 3.3 POWERING UP A 6C105 WITH AC POWER SUPPLIES3-12 Chapter 3 6C105 SetupDC Power Supply Requirement for Each Supply 6C105 Overview and Setup Guide3.4.1 Connecting a 6C205-2 to a 48/60 VDC Power Source 3.5.1 Removing the Fan Tray 3.5 REMOVING AND REINSTALLING THE FAN TRAYIn the following step ensure that you do not force the fan tray 3.5.2 Reinstalling the Fan Trayinto place, as it may damage the unit 4. Slide the fan tray forward until the faceplate of the tray is flush with the face of the 6C105. If there is any strong resistance, remove the fan tray and reinsert it 3-17 Removing and Reinstalling the Fan Tray6C105 Overview and Setup Guide Figure 3-9 Reinstalling the Fan Tray6C105 Overview and Setup Guide Chapter 3 6C105 Setup3-18