Manuals / Cabletron Systems / Household Appliance / Plumbing Product

Cabletron Systems SEHI100TX-22 manual 7.7.1 Conﬁguring the Trap Table

Models: SEHI100TX-22

1 88

Download 88 pages 20.99 Kb

Page 65

7.7.1Conﬁguring the Trap Table

The Trap Table Screen

SNMP Community Name

Displays the community name included in the trap message sent to the Network Management Station with the associated IP address.

Traps

Enables transmission of the traps to the network management station with the associated IP address.

Trap IP Address

Indicates the IP address of the workstation to receive trap alarms from the SEHI.

7.7.1Conﬁguring the Trap Table

Use the following steps to conﬁgure the Trap Table:

1.Use the arrow keys to highlight the SNMP Community Name field, then enter the community name.

2.Press ENTER.

3.Use the arrow keys to highlight the Traps field and enter Y to send alarms from the SEHI to the workstation, or N to prevent alarms from being sent.

4.Press ENTER.

5.Use the arrow keys to highlight the appropriate Trap IP Address field.

6.Enter the IP address of the workstation that you want to send traps to in this field. The format for this entry is XXX.XXX.XXX.XXX, with the value of XXX ranging from 0 to 255, and three dots, or else it returns to the beginning of the field.

7.Use the arrow keys to highlight the SAVE option, then press ENTER or F6. The “SAVED OK” message appears indicating that the changes have been saved to memory.

NOTE

The ﬁrst time an attempt is made to exit the screen without saving the changes, a “NOT SAVED?” message is displayed. The edits are lost if the user proceeds to exit without saving the changes.

SEHI100TX User’s Guide

7-17

Image 65

Cabletron Systems SEHI100TX-22 manual 7.7.1 Conﬁguring the Trap Table

Contents

SEHI100TX-22 100BASE-T INTELLIGENT STACKABLE HUB USER’S GUIDE Page SEHI100TX User’s Guide Only qualiﬁed personnel should perform installation proceduresFCC NOTICE VCCI NOTICE DOC NOTICECABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT SEHI100TX User’s GuideCABLETRON SOFTWARE PROGRAM LICENSE EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITYUNITED STATES GOVERNMENT RESTRICTED RIGHTS SEHI100TX User’s GuideSEHI100TX User’s Guide DECLARATION OF CONFORMITYCHAPTER 2 SEHI FEATURES AND OPTIONS CONTENTSINSTALLATION REQUIREMENTS AND SPECIFICATIONSCHAPTER 5 CONNECTING TO THE NETWORK ContentsTROUBLESHOOTING CHAPTEREPIM SPECIFICATIONS ContentsAPPENDIX B IMAGE FILE DOWNLOAD USING OID STRINGS APPENDIX ASEHI100TX User’s Guide Contentsviii CHAPTER INTRODUCTION 1.1 USING THIS MANUAL1.2 DOCUMENT CONVENTIONS your email address 1.3 GETTING HELPanonymous SEHI100TX User’s Guide 1.4 RELATED MANUALSChapter 1 Introduction 2.1 SEHI OVERVIEW CHAPTER SEHI FEATURES AND OPTIONS2.2 SEHI FEATURES RESET Button 2.3 STACKABLE CAPABILITIESLANVIEW LEDs Local Management2.6 OPTIONAL EPIMS 2.4 RACK MOUNTING CAPABILITIES2.5 REMOTE NETWORK MANAGEMENT 3.1.1 HubSTACK Interconnect Cable Requirements CHAPTER INSTALLATION REQUIREMENTS AND SPECIFICATIONS3.1 CABLE SPECIFICATIONS 3.1.2 UTP Cable Speciﬁcations Propagation Delay 3.1.3 Multimode Fiber Optic Cable SpeciﬁcationsTemperature Fiber Optic Budget and Propagation Delay3.2 NETWORK CABLE LENGTHS A DTE Network Cable LengthsSEHI100TX-22 Repeater B DTE The maximum length of an individual UTP segment may be no3.4 COM PORT REQUIREMENTS 3.3 NETWORK PORT SPECIFICATIONS3.5.1 Power Supply Requirements 3.5 OPERATING SPECIFICATIONS3.5.2 Environmental Requirements 3.5.3 Agency ApprovalsDimensions H x W x D 3.6 PHYSICAL SPECIFICATIONSWeight Chapter 3 Installation Requirements and Speciﬁcations4.1 UNPACKING THE SEHI CHAPTER INSTALLATIONRear of Chassis NVRAM Switch located behind grating 4.2 PRE-INSTALLATION CHECKOUTProceed to Section 4.5, Powering Up and Stacking the SEHI 4.3 TABLETOP OR SHELF INSTALLATION4.4 RACKMOUNT INSTALLATION Rack mounting the SEHI involves the following Rack Mounting the SEHI Figure 4-4 Installing the Rack Mounting BracketsFasten the SEHI to the equipment rack securely Proceed to Section 4.5, Powering Up and Stacking the SEHI4.5 POWERING UP AND STACKING THE SEHI 7. Repeat steps 3 through 6 until all SEH hubs are connected 4.6 INSTALLING AN EPIM SEHI100TX User’s Guide Chapter 4 Installation4-10 5.1.1 Connecting to Network Ports CHAPTER CONNECTING TO THE NETWORK5.1 CONNECTING THE SEHI TO THE NETWORK 5.1.2 Connecting to an EPIM-100TX 6. TX Figure 5-2 EPIM-100TX Crossover SwitchPosition X crossed over 5.1.3 Connecting to an EPIM-100FX or EPIM-100FMB SEHI100TX User’s Guide 5.2 TESTING THE INSTALLATIONTesting the Installation SEHI100TX User’s Guide Chapter 5 Connecting to the Network6.1 INSTALLATION TEST CHAPTER TROUBLESHOOTING6.2 USING LANVIEW Blinking indicates a steady LED pulse SEHI100TX-22Flashing indicates an irregular LED pulse 6.3 USING THE RESET BUTTON 6.4 SETTING THE NVRAM SWITCH SEHI100TX User’s Guide Chapter 6 TroubleshootingCHAPTER LOCAL MANAGEMENT Chapter 7 Local Management 7.1 KEYBOARD CONVENTIONSSEHI100TX User’s Guide Table 7-1 Keyboard Conventions7.2 MANAGEMENT TERMINAL SETUP Connect the console cable to the SEHI as follows Management Terminal Setup Parameters 7.3 ACCESSING LOCAL MANAGEMENT 3. Press ENTER Figure 7-3 Feature Selection Screen 7.4 THE FEATURE SELECTION SCREENFigure 7-4 Community Name Table Screen 7.5 THE COMMUNITY NAME TABLE SCREENACCESS write access to Local Management. Super-UserThis allows the user to read and write to Local COMMUNITY NAME7.5.1 Editing the Community Name Field 7.6 THE CONFIGURATION SCREEN 7.6.1 Setting the IP Address Consult the Network Administrator prior to setting the Subnet Mask 7.6.2 Setting the Subnet Mask7.6.5 Exiting the Conﬁguration Screen 7.6.3 Setting the Default Gateway7.6.4 Using the Port Enable Override 7.7 THE TRAP TABLE SCREEN 7.7.1 Conﬁguring the Trap Table 7.8 THE SNMP TOOLS SCREEN 7.7.2 Exiting the Trap Table ScreenThe following sections describe SNMP Tools screen ﬁelds 7.8.1 Getting Individual OIDs 7.8.2 Getting the Next OID 7.8.3 Setting an OID7.8.5 Walking Through OIDs 7.8.4 Viewing Multiple OIDs7.8.7 Cycling Through OIDs 7.8.6 Stepping Through OIDs7.8.8 Repeating the Last OID 7.8.9 Exiting the SNMP Tools Screen7.9 THE DEVICE STATISTICS SCREEN Displays the number of errors received This command lets the user enable the selected port 7.9.1 Selecting the Appropriate Module/Port 7.9.2 Using the ENABLE PORT Command7.9.3 Using the DISABLE PORT Command 7.9.5 Exiting the Device Statistics Screen 7.9.4 Setting the UPDATE-FREQency FieldA.1.1 EPIM-100TX APPENDIX A EPIM SPECIFICATIONSA.1 EPIM SPECIFICATIONS Appendix A EPIM Speciﬁcations A.1.2 EPIM-100FXA.1.3 EPIM-100FMB SEHI100TX User’s Guide Appendix A EPIM SpeciﬁcationsAPPENDIX B IMAGE FILE DOWNLOAD USING OID STRINGS B.1 SETTING UNIX WORKSTATION AS TFTP SERVER B.2 STANDARD LOCAL DOWNLOAD Table B-1 OIDs and Settings Appendix B Image File Download Using OID StringsSEHI100TX User’s Guide StepNumerics INDEXSEHI100TX User’s Guide Index-1Page GERMAN POWER SUPPLY CORDSPANISH FRENCH