Cabletron Systems SmartCell 6A000 T, U, V, W

SmartCell 6A000 User Guide I-3

Index

start operator.............................................2-9

stop lecs command...................................3-6

sustainable cell rate (SCR).....................4-18

switch-attribute.........................................2-8

T

technical support..................................... C-1

telnet connection ......................................2-8

TFTP server..............................................4-2

The..........................................................4-14

traffic descriptors ...................................4-18

traffic management.................................4-18

trapcommunity command........................B-5

troubleshooting

IP over ATM......................................5-1

troubleshooting congestion......................5-3

troublleshooting

LAN emulation.................................. 5-2

trustednms command.............................. B-5

U

UNI 3.0/3.1 ILMI MIB........................... B-1

UNI routes................................................4-9

UNI3.0....................................................4-19

UNI3.1....................................................4-19

UNI4.0....................................................4-18

unpacking the switch................................2-1

update firmware command....................... 4-2

upgrading operating software...................4-2

using the console......................................2-8

V

vccmask parameter.................................4-16

VLAN

creating ..............................................3-1

VPI/VCI pairs.........................................4-16

W

warranty...................................................C-3

well known LECS address....................... 3-3

Contents

Main NOTICE FCC CLASS A NOTICE DOC CLASS A NOTICE DECLARATION OF CONFORMITY ADDENDUM Page Page Page REVISION HISTORY Date Revision Description TABLE OF CONTENTS 5 Troubleshootin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1 Page Page LIST OF FIGURES Page LIST OF TABLES Page 1 INTRODUCTION Page 2 SWITCH INSTALLATION AND SETUP 2.1 UNPACKING THE SWITCH 2.2 INSPECTING THE SWITCH 2-2 SmartCell 6A000 User Guide Inspectin 2.3 INSTALLING THE SWITCH 155 Mbps STS-3c/STM-1 UTP5, 4 Ports 155 Mbps STS-3c/STM-1 SMF/MMF, 4 Ports MMF, 4 Ports 155 Mbps STS-3c/STM-1 Page Page 2.4 CONFIGURING THE SWITCH Page 2.5 USING THE CONSOLE 2.5.1 Console Commands Addin and Modif y in As with the show command, each prompt provides you with a default. For example 2.5.2 Console Help 3 IP OVER ATM AND LANE 3.1 CREATING AN IP OVER ATM VLAN 3.1.1 ATM Addressin for IP over ATM 3.2 CREATING AN EMULATED LAN 2. Create an ELAN on your switch by executing the add elan command. The following is an example: 3. Create a client for the switch on the ELAN. For example, enter 5. Physically connect your end nodes and edge devices to the switch ports. Note When you create a client, it automatically finds the LECS address using ILMI. 4. Enter the show client command to make certain that the client is operational. Page 3.2.2 ELANs Across Multiple Switches 3.2.3 Switch Clients 4 SWITCH ADMINISTRATION 4.1 BACKING UP AND RESTORING SWITCH CONFIGURATION 4.2 UPGRADING OPERATING SOFTWARE 4.2.1 Unsuccessful Update 4.2.2 Usin the df Command to Recover 4.3 SETTING UP ROUTES 4.3.1 IISP Routin Creatin IISP Routes IISP Routes Amon Multiple Switches Default IISP Routes IISP Routes and Network Topolo gy Routin 11:22 : 11:22:4411:22:55 A B C IISP Metrics and Load Sharin 4.3.2 UNI Routes Page 4.4 LOGS AND ALARMS 4.4.1 Lo Messa e System 4.5 SETTING UP PVC CONNECTIONS 4.5.1 Point-to-Point PVCs Connectin to Local Client Throu h Point-to-Point PVC 4.5.2 Point-to-Multipoint PVCs 4.5.3 Non-zero VPIs 1. Use set vccmask to change the VPI/VCI values to 3/9. Note Do not set the VCI part of the VCCMask to fewer than 5 bits. 2. Use the show vccmask command to see the new VPI/VCI combination. 3. Use the set portconfig command to reconfigure a port to use the new values for VPI and VCI. For example, to set up a PVC on port A1 using the new VPI/VCI bit ranges (3/9), enter 4. Use show portconfig to see the change to port A1. PVCs can be configured for port A1 using VPI values from 0 to 7 and VCI values from 0 to 511. 4.6 TRAFFIC MANAGEMENT Page 4.6.2 Call Admission Control Policy 4.6.3 Class of Service Queues Class of Service Queue Allocation Guidelines 4.6.4 EFCI, EPD, and RM Thresholds Page 5 TROUBLESHOOTING 5.1 TROUBLESHOOTING IP OVER ATM - - - - - - - - - - - 5.2 TROUBLESHOOTING LAN EMULATION - - - - - - - - - - 5.3 TROUBLESHOOTING CONGESTION 5.3.3 Port Con estion Page Page APPENDIX A FEATURES AND SPECIFICATIONS A.1 HARDWARE COMPONENTS A.1.1 Front Panel Fi g A.1.2 CPU Module A.1.3 Switch Modules (MSM and ESM) A.1.4 Input/Output (Port) Modules 155 Mbps STS-3c/STM-1 UTP5, 4 Ports 155 Mbps STS-3c/STM-1 SMF/MMF, 4 Ports MMF, 4 Ports 155 Mbps STS-3c/STM-1 Port Numberin A.2 FEATURES Page A.3 SPECIFICATIONS A.3.1 Technical Specifications A.3.2 Physical Specifications A.3.3 ATM Port Specifications A.3.4 Standards Specifications A.3.5 CPU Serial Port Pin-Out Descriptions Page Page APPENDIX B SMARTCELL 6A000 AND SNMP B.1 INTERNET MIB HIERARCHY B.2 ZEITNET PROPRIETARY MIB tt B.2.1 Interpretin the Object Identifier B.2.2 Proprietary MIB Functions B.3 A CLIENT FOR SNMP MANAGEMENT B.4 CONSOLE COMMANDS THAT AFFECT THE AGENT B.5 MIB EXCEPTIONS Page Page Page APPENDIX C TECHNICAL SUPPORT C.1 TELEPHONE ASSISTANCE C.2 FAX SERVICE C.3 ELECTRONIC SERVICES C.4 PLACING A SUPPORT CALL C.5 HARDWARE WARRANTY C.6 SOFTWARE WARRANTY C.7 REPAIR SERVICES APPENDIX D ACRONYMS A B C D E F G H I J K L M N O P Q R S T U V W Page INDEX A B C D L M O P Q T U V W